7.5inch e-Paper

Introduction

Note: The raw panel require a driver board, If you are the first time use this e-Paper, we recommend you to buy the HAT version or buy more one driver hat for easy use, otherwise you need to make the driver board yourself.And this instruction is based on the HAT version.

800x480, 7.5inch E-Ink display HAT for Raspberry Pi, SPI interface

【Version update instructions】：

This product has been updated to V2 version with higher resolution, supporting 800x480 resolution (V1 version has 640x384 resolution)

The hardware structure and interface of V2 version of this product are compatible with V1 version, but the software needs to be updated

Interfaces

VCC	3.3V
GND	GND
DIN	SPI MOSI
CLK	SPI SCK
CS	SPI chip select (Low active)
DC	Data/Command control pin (High for data, and low for command)
RST	External reset pin (Low for reset)
BUSY	Busy state output pin (Low for busy)

Working principle

Introduction

This product is an E-paper device adopting the image display technology of Microencapsulated Electrophoretic Display, MED. The initial approach is to create tiny spheres, in which the charged color pigments are suspending in the transparent oil and would move depending on the electronic charge. The E-paper screen display patterns by reflecting the ambient light, so it has no background light requirement. Under sunshine, the E-paper screen still has high visibility with a wide viewing angle of 180 degree. It is the ideal choice for E-reading.

Communication protocol

Note: Different from the traditional SPI protocol, the data line from the slave to the master is hidden since the device only has display requirement.

CS is slave chip select, when CS is low, the chip is enabled.
DC is data/command control pin, when DC = 0, write command, when DC = 1, write data.
SCLK is the SPI communication clock.
SDIN is the data line from the master to the slave in SPI communication.

SPI communication has data transfer timing, which is combined by CPHA and CPOL.

CPOL determines the level of the serial synchronous clock at idle state. When CPOL = 0, the level is Low. However, CPOL has little effect to the transmission.
CPHA determines data is collected at the first clock edge or at the second clock edge of serial synchronous clock; when CPHL = 0, data is collected at the first clock edge.

There are 4 SPI communication modes. SPI0 is commonly used, in which CPHL = 0, CPOL = 0.

As you can see from the figure above, data transmission starts at the first falling edge of SCLK, and 8 bits of data are transferred in one clock cycle. In here, SPI0 is in used, and data is transferred by bits, MSB first.

Documentation

Instruction about make new font

Schematic

Demo code

Github

Datasheets

Related Resources

This is a post in Arduino Form about our SPI e-Paper thanks to ZinggJM, maybe you want to refer to.

Waveshare e-Paper display with SPI

Related applications (shared by user)

Question:

Working requirements of e-Paper?

Answer:

Two-color B/W e-paper
- 【Working】Temperature: 0~50°C; Humidity: 35%~65%RH
- 【Storage】Temperature: ≤30°C; Humidity: ≤55%RH; Max storage time: 6 months
- 【Transport】Temperature: -25~70°C; Max transport time: 10 days
- 【Unpack】Temperature: 20°C±5°C; Humidity: 50%RH±5%RH; Max storage time: Should be assembled in 72h
Three-Color e-Paper
- 【Working】Temperature: 0~40°C; Humidity: 35%~65%RH
- 【Storage】Temperature: ≤30°C; Humidity: ≤55%RH; Max storage time: 3 months
- 【Transport】Temperature: -25~60°C; Max transport time: 10 days
- 【Unpack】Temperature: 20°C±5°C; Humidity: 50%RH±5%RH; Max storage time: Should be assembled in 72h

When store three-color e-Paper, please refresh it to white, and keep the screen upward. Note that you need to update it at least every three months.

Question:

What do you need to note about e-Paper refreshing?

Answer:

Refresh mode
- Full refresh: e-Paper flicker when full refreshing to remove ghost image for best display.
- Partial refresh: It don't flicker if you use partial refresh (only some of the two-color e-paper support partial refresh). Note that you cannot use Partial refresh all the time, you should full refresh e-paper regularly, otherwise, ghost problem will get worse even damage.
Refresh rate
- When using, you should set the update interval at least 180s.(except Partial supportable types)
- Please set the e-Paper to sleep mode or power off it directly, otherwise, the e-Paper is damaged because of working in high voltage for long time.
- You need to update the content of three-color e-Paper at least one time every 24h to avoid from burn-in problem.
Working place
We recommend you to use the e-Paper indoor. If you need to set the e-paper outdoor, Please place the e-paper in shadow and protect it from UV. When you designed you e-paper product, you should take care about the working situation like temperature, humidity, etc.

Question:

How much could the flexible e-paper be bended

[Collapse] Answer:

The IC part of e-Paper cannot be bended, you can bend the display area in degree larger than 60°C

Question:

Why the e-Paper cant work with Arduino?

Answer:

The I/O level of Arduino is 5V, and the e-Paper should be driven with 3V3. If your Arduino cant drive the e-Paper successfully, please try to convert the level to 3.3V

You can also try to connect the Vcc pin to the 5V of Arduino to see whether the e-Paper works, but we recommend you not to use 5V for a long time.

Question:

Why does the color of e-Paper look a little black or grey?

Answer:

You can try to change the value of Vcom on demo codes.

Question:

Three-color e-paper looks more red/yellow than the picture on website?

Answer:

Because of different batch, some of them have aberration. Store the e-Paper right side up will reduce it. And if the e-Paper didn't be refreshed for long time, it will become more and more red/yellow. Please use the demo code to refresh the e-paper for several times in this case.

Question:

Why my e-paper has ghosting problem after working for some days

Answer:

Please set the e-paper to sleep mode or disconnect it if you needn't refresh the e-paper but need to power on your development board or Raspberry Pi for long time.Otherwise, the voltage of panel keeps high and it will damage the panel

Question:

Why the FPC of the e-Paper is broken after using for some times?

Answer:

Please make sure you have used it in correct way.

TAG： Omni-Directional Lidar DDSM115 Direct Drive Servo Motor All-In-One Design Hub RS485 Motor Mini TOF Time-of-Flight Laser Ranging Radar Sensor Compatible with Arduino Raspberry Pi ESP32 and Pico Changeable Photo Raspberry Pi 5 Audio PC Monitor Screen Python HTTP Request Communication CH340 driver ESP32 S3 Development Board 1.9 inch LCD Capacitive Touch Screen 1.9inch Display 170×320 N16R8 STM32 0.96inch RGB OLED Raspberry Pi 5 PCIe to USB Gen1 HUB and M.2 NVMe SSD PI5 Expansion board HAT+ UNO Minima RA4M1 Tiny SuperMini R7FA4M1 Board Compatible With R4 For Arduino MPS2280D Raspberry Pi 5 PCIe to M.2 NVMe Dual SSD Adapter Board HAT Pi5 Double 2280 ESP32-S3 1.43inch AMOLED Display AI Development Board 466×466 1.43 inch TouchScreen Deepseek Attitude Sensor Raspberry Pi CSI-to-HDMI Servo RS485 Bus Raspberry Pi display Raspberry Pi 5

7.5inch E Ink raw display, black, white, 800×480

TAG： Rasberry Pi 5 PCIe TO MiniPCIe GbE USB HUB HAT+ Hub RJ45 SIM7600G-H EG25-G 4G Raspberry Pi 5 PCIe to NVMe ESP32-S3 1.28inch Round LCD Display TouchScreen Accelerometer Gyroscope Sensor Case TTL To CAN Mini Luckfox Pico Rv1106 Core1106 Smart 86 TV Box Development Board With 4 inch LCD Display TouchScreen Relay RS485 CM4S08032 Compute Module PoE Board Raspberry Pi CM4S CM3 3Lite 3 3+Lite PoE ADXL354CEZ LuckFox ESP32 C6 Development board 1.9 inch LCD display 1.9inch Screen 172&amp;times;320 With SD slot RGB LED QMI8658 6-Axis-Sensor ST7789 CST816 Core3566002000 RAM Monitor Screen RM502Q AE IoT EMBB 5G 4G 3G M.2 LTE-A/NSA SA GNSS DFOTA VoLTE Quectel Raspberry Pi 5 Gen3 Raspberry Pi 5 PCIe USB3.2 Gen1 Hub Raspberry Pi Pico 2 RP2350 Pico2 ARM Cortex-M33 RISC-V Hazard3 Jetson Nano Development Board IO-BASE-A For JETSON NANO B01 Spotpear CSI Camera Arduino IR Thermal Imaging Camera Pico-DALI2 ESP32 C6 S3 DALI