• sales

    +86-0755-88291180

2.7inch e-Paper (B)

Introduction


Note:
 The raw panel require a driver board, If you are the first time use this e-Paper, we recommend you to buy the HAT version or buy more one driver hat for easy use, otherwise you need to make the driver board yourself. And this instruction is based on the version with PCB or driver board.

264x176, 2.7inch E-Ink display HAT for Raspberry Pi, three-color


Interfaces


VCC3.3V
GNDGND
DINSPI MOSI
CLKSPI SCK
CSSPI chip select (Low active)
DCData/Command control pin (High for data, and low for command)
RSTExternal reset pin (Low for reset)
BUSYBusy state output pin (Low for busy)


Working principle


Introduction


This product is an E-paper device adopting the image display technology of Microencapsulated Electrophoretic Display, MED. The initial approach is to create tiny spheres, in which the charged color pigments are suspending in the transparent oil and would move depending on the electronic charge. The E-paper screen display patterns by reflecting the ambient light, so it has no background light requirement. Under sunshine, the E-paper screen still has high visibility with a wide viewing angle of 180 degree. It is the ideal choice for E-reading.


Communication protocol






Note: Different from the traditional SPI protocol, the data line from the slave to the master is hidden since the device only has display requirement.

  • CS is slave chip select, when CS is low, the chip is enabled.
  • DC is data/command control pin, when DC = 0, write command, when DC = 1, write data.
  • SCLK is the SPI communication clock.
  • SDIN is the data line from the master to the slave in SPI communication.

SPI communication has data transfer timing, which is combined by CPHA and CPOL.

  1. CPOL determines the level of the serial synchronous clock at idle state. When CPOL = 0, the level is Low. However, CPOL has little effect to the transmission.
  2. CPHA determines whether data is collected at the first clock edge or at the second clock edge of serial synchronous clock; when CPHL = 0, data is collected at the first clock edge.
  • There are 4 SPI communication modes. SPI0 is commonly used, in which CPHL = 0, CPOL = 0.

As you can see from the figure above, data transmission starts at the first falling edge of SCLK, and 8 bits of data are transferred in one clock cycle. In here, SPI0 is in used, and data is transferred by bits, MSB first.


TAG: Arduino Thermal imaging AI Board ESP32 S3 Development Board 3.5 inch LCD Capacitive Touch Screen 3.5inch Display 240×320 N16R8 Raspberry Pi 0.96inch LCD Arducam 64MP Camera Raspberry Pi 60GHz mmWave Radar Sensor High-Precision Human Body PCR For Arduino ESP32 Pi5 Heatsink ESP32-C6 2.8inch LCD Display Capacitive AI Development Board 240×320 2.8 inch TouchScreen Raspberry Pi 5 Case Raspberry Pi Pico 2 RP2350-Zero Mini Board RP2350A Raspberry Pi Pico 1024×600 Raspberry Pi Pico 2 RP2350A Audio Box 1.85-inch LCD Round 1.85inch TouchScreen Speaker 360x360 Raspberry Pi Pico 2 RP2350/RP2040 W5100S-EVB-Pico W6300-EVB-Pico2 Ethernet Development Board ETH RJ45 Raspberry Pi GPS GNSS Expansion Board L76K Beidou (BDS) GLONASS QZSS A-GNSS Also For Jeston Raspberry Pi 3 display HAT X1006 Raspberry Pi 5 PCIe To 2.5 SATA And M.2 KEY-B 2280 SSD/HDD Double-SATA (NOT BOOT From SATA/SSD PoE-M.2-HAT+B User Guide MP2.5GD Raspberry Pi 5 PCIe to Dual 2.5G Double Ethernet HAT Pi5 RTL8125 Modbus POE ETH Relay MQTT User Guide Computer Monitor Screen