STM32 ST-LINK/V2 (CN) User Guide

Introduction

User Manual

Resources

Question:

STLINK/V2 does not have a CD-ROM? Why not distribute the CD?

Answer:

Yes, this is ST official original, there is no CD itself. However, we can provide you with a link to download the product information from the web disk. You can look at the pictures of the product introduction, software, etc. to be downloaded from the Internet. The driver is also downloaded from the Internet.

We also don’t know why we don’t have an extra CD to make the operation easier and more convenient for customers. It may not consider these difficulties of users when it launches the product. Not having a CD is very troublesome, sorry, but we can't arrange it, because the original factory does not have it as standard. We stock many sets here, all of which are the same.

You can send an email to the official website and make suggestions.

Question:

Is your ST-LINK/V2 (CN) not original? The product picture I saw on the official website www.ST.com is different from yours.

Answer:

Hello, it should be that you did not read it carefully. Open the PDF corresponding to the official website page. There are 2 places where the version is mentioned. As shown below:

In fact, ST-LINK/V2 is subdivided into 2 versions: ST-LINK/V2 and ST-LINK/V2-ISOL. Our company currently supplies ST-LINK/V2, which guarantees 100% brand new original authenticity.

Question:

When designing the download circuit, do I need to supply power to ST-LINK?

Answer:

It must be powered, that is, at least one of these 2 pins inputs 3.3V from the outside

Question:

When programming STM8, the board cannot input power from the outside, what should I do?

Answer:

Note: This step may burn out the downloader and target board and lose the ST warranty. Please operate with caution!
Note: This step may burn out the downloader and target board and lose the ST warranty. Please operate with caution!
Note: This step may burn out the downloader and target board and lose the ST warranty. Please operate with caution!

The normal download of STM8 is connected to the target board through the SWIM interface, and the target board is connected to an external power supply.

However, some customers do not have external power supply on the target board due to design errors or cost-saving reasons during research and development, and normal ST-LINK cannot be downloaded.

The following two points need to be short-circuited. At this time, the downloader can supply power to the target board (it is best to use a fuse to short-circuit, if there is no fuse, it can be short-circuited directly, but make sure that there is no short-circuit inside the target board!)

Question:

In keil, the program can be downloaded and run normally, but an error similar to the following appears when debugging?

Cannot access Memory
Error while accessing a target resource. The resource is perhaps not available or a wrong access was attempted.
*** error 57: illegal address (0x08000000)

Answer:

Uncheck the Download to Flash option in the Options for Target-"Debug-"Settings-"Debug-"Download Options dialog box.

Question:

When using STLINK-V3SET, the downloader can be recognized by keil software and the chip ID can be read, but the following error is reported?

Answer:

Look at the keil version number, at least 5.25 can be used

Question:

How to download STVP software on ST official website?

Answer:

Open the STVP download link:

http://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/stvp-stm32.html

Find "Get Software" to get the software

Click to agree to the agreement

Fill in your name (pinyin), email address, tick it, click "download" to download, ST will send a link to your mailbox, click the link, and repeat the "first step" to download the software.

To：

Dear Customers, There may be a lag of several hours before we could process your order, depending on the time difference between your location and ours. Sincerely hoping your understanding!

Email(support)

services01@spotpear.com

TAG： Industrial Isolation USB TO RS232/485/422/TTL FT232RNL Serial UART Converter ESP32 S3 R8 MP3 Board 2.8inch LCD TouchScreen Display Speaker/SD-Card/Battery/QMI8658-6-Axis-Sensor Raspberry Pi CM5 Industrial Module 4G/5G/LoRa Gigabit Ethernet RJ45 Raspberry Pi RP2040 LoRa-HF MLX90641 Raspberry Pi Pico 2 RP2350A 1.54inch TouchScreen 1.54 inch LCD Display Development Board 240×240 7inch Monitor Display RISC-V AI Machine Vision Kit OAK-D-POE JPEG Encoder 12MP IP67 Waterproof 4TOPS OpenCV Camera JETSON NANO MINI Computer Secondary Screen SpotPear Industrial Modbus RTU RS485 4-ch Relay With isolation protection and guide rail Jetson Nano Modbus POE ETH Relay MQTT User Guide PC USB Monitor Screen Development Board PC Secondary Screen Arduino MLX90641 X1300 X1300-A2 Raspberry Pi 5 HDMI to CSI-2 Shield 1080P@60fps & Audio & Video Also

ST LINK/V2 (CN) STM32 ST8 Programmers and Debuggers

TAG： 8 50mm Zoom C Lens Raspberry Pi High Quality Camera Global Shutter ESP32-S3-Zero Raspberry Pi Pico 2 RP2350/RP2040 W5100S-EVB-Pico W6300-EVB-Pico2 Ethernet Development Board ETH RJ45 ESP32 C3 Round LCD Electronic EYE 0.71 inch Display Watch Screen GC9D01 160x160 Arduino 1.5inch LCD USB to UART Raspberry Pi Official Original POE Plus HAT Injector 30W Power Over Ethernet 802.3af/at For Pi5 Onboard RGB LED For RJ-45 EIA 568A/568B Port Luckfox Pico RJ45 voice module Raspberry Pi 5 PCIe M.2 NVMe SSD Raspberry Pi Camera 12MP Sony IMX708 autofocus HDR Module 3 Sensor Assembly ESP32 S3 1.43 inch AMOLED Display Screen Arduino LVGL SD-Port QMI8658C 6-Axis Sensor Raspberry Pi Pico 2 RP2350B RP2350-PiZero Development Board PSRAM DVI For HDMI Raspberry Pi Pico 2 RP2350A USB-C Mini Development Board 1.54inch LCD TouchScreen Display 240×240 ST7789S For Arduino /Raspberry Pi /ESP32 /Pico /STM32 Raspberry Pi 5 Active Cooler RP2040 ESP32 Thermal imaging 2.13Inch E-Ink Industrial 4-ch RS485 DC Detection Module Modbus RTU DIN Rail