• sales

    +86-0755-88291180

DTM3202 voice module user guide

Resource

DTM3202


Step 1】 Functional Overview

Supports direct USB update of voice content, with adjustable volume.

Supports memory cards up to 32G.

Provides a 12V output voltage; outputs 12V voltage during sound playback.

Ten channels of one-to-one voice control (can trigger 10 different voices).

Supports control via a microcontroller's serial port, TTL serial communication, single-wire serial communication.

Ten channels of voice can be individually set for each type of voice playback mode (pulse repeatable, level hold loop, etc.).

It is possible to set the device to automatically cycle through all voices upon power-up.

Step 2】Electrical Parameters

Operating voltage: DC6V~35V

Rated output power: 20W/8Ω

Audio format: MP3

Maximum working current: 1000mA

Working environment temperature: -40~+85℃ industrial grade standard

Working environment humidity: 10%~98%

Step 3】Audio File Naming Rules

Audio files must be in MP3 format; if the files are generated through voice synthesis software, they can be copied directly.

Note: The order of the sounds is arranged by the filename. The filenames should be named with a 5-digit number, that is: 00001, 00002......00010

00001.mp3 corresponds to Voice 1

00002.mp3 corresponds to Voice 2

00003.mp3 corresponds to Voice 3

......

00010.mp3 corresponds to Voice 10


Step 4】Configuration Instructions for 1-10 Channels Voice Playback Mode

If the playback mode for channels 1-10 has not been configured, the default mode is: Pulse Repeatable Mode.

Other playback modes can be configured using our company's "IO Port Function Configuration Software" as shown below:

After configuring each IO port, click "Generate Configuration", and then save the configuration file to the desktop, with the filename as config.bin.

Then copy the config.bin file to the TF card.
IO9 and IO10 are by default set for serial port control. If these two ports are to be set for IO-triggered playback,
they need to be set in the "Serial Port Configuration" section of the software, to the mode shown in the following diagram:



 Step 5】IO Combination Playback

Through IO port combination playback, up to 1023 sections of voice are supported. This can be set via the PC software to "Play Once and Stop" or "Loop Playback".

An unconnected (floating) IO port represents "1", while connection to GND (Ground) represents "0".


For using more combination segments, please refer to the "IO Combination Playback Query Table".

 Step 6】Serial Port Control Instructions

This module supports single-wire serial port and TTL serial port control.

For single-wire serial port, the control port needs to configure IO8 as "single-wire serial port".

First, use the "IO Port Function Configuration Software" to set IO8 as a single-wire serial port, leave others as default, as shown in the following diagram:

Click "Generate Configuration", then save the configuration file to the desktop, with the filename as config.bin. After that, copy the config.bin file to the TF card.

The control pin for the single-wire serial port is on the "ONE" interface on the board, as shown in the following diagram:

The communication protocol refers to the "DTM Serial Communication Protocol".

TTL Two-Wire Serial Control

The TTL two-wire serial control pins are on the "RX, TX" interface on the board, as shown in the following diagram:


 Step 7】Interface Description



Step 8】Size


TAG: Raspberry Pi 5/4B not boot To update BootLoader EEPROM Tutorial IMX462 FT4232HL USB TTL RS232 Industrial UART 4-Ch UART Raspberry Pi 8inch LCD 768x1024 Capacitive TouchScreen HDMI Display ESP32-S3 Mini LCC-14 Raspberry Pi DSI 800×480 Argon Neo 5 Industrial RS232 to RS485 DeepSeek XiaoZhi AI Voice Chat Robot BOX ESP32-S3 Development Board 3.5 inch LCD N16R8 Touchscreen Display 6-Axis /Camera /SD Raspberry Pi Zero 4G Cat1 With USB Hub Expansion Board LTE/GPS/EA/EU also For Zero 2W X1008 Raspberry Pi 5 PCIe to 2.5" 3.5" SATA HDD/SSD Dual Double-SATA (NOT BOOT From SATA/SSD Raspberry Pi DS3231 Raspberry Pi ZERO ESP32 2 inch Capacitive TouchScreen LCD Display ST7789 CST816D 240x320 For Arduino/Raspberry Pi/Pico 7.5 inch Passive NFC e-Paper BW Display 7.5inch E-ink Screen No Need Battery Wireless Powered Data Transfer Raspberry Pi DSI Raspberry Pi 5 8 inch DSI LCD Captive TouchScreen MIPI Display 1280x800 Industrial One-Body Tablet PC With 5MP Front Camera RP2040-PiZero Raspberry Pi 5 8mp Camera