• sales

    +86-0755-88291180

ESP32 T-HMI 2.8inch User Guide

【Quick start】

The board uses USB as the JTAG upload port. When printing serial port information on USB, it is necessary to turn on CDC_ ON_ BOOT configuration. If the port cannot be found when uploading the program, or if USB is already used for other functions, the port will not appear. Please manually enter upload mode.

[] Press and hold the power on button when shutting down, which is located behind the RST button.

[] After connecting USB, first press and hold the start button, then click reset, and then release the start button


【Arduino】

[] On the Settings tab of Arduino preferences, enter https://raw . githubusercontent . com/espressif/arduino-esp32/GH-pages/package _ esp32 _ index . JSON URL other board manager URL input box.

[] Click OK and the software will be installed.

[] Search for ESP32 in Tools>Board Manager and install the ESP32 Arduino SDK (version 2.0.3 or higher)

[] Copy all the contents in the lib folder of this repository to the Arduino repository folder.(Take for example c:\ Users \ your name \ Documents \ Arduino \ libraries)

[] Select the correct settings in the Tools menu, as shown below.

SettingValue
BoardESP32 S3 Dev Module
USB CDC On BootEnabled
CPU Frequency240MHz (WiFi)
Core Debug LevelNone
USB DFU On BootEnabled
Events Run OnCore 1
Flash ModeQIO 80MHz
Flash Size16MB (128Mb)
JTAG AdapterIntegrated USB JTAG
Arduino Runs OnCore 1
USB Firmware MSC On BootDisabled
Partition SchemeHuge APP (3MB No OTA/1MB SPIFFS)
PSRAMOPI PSRAM
USB ModeHardware CDC and JTAG

【Platform video】

[] PlatformIO plugin installation: Click on the left column extension → Search for PlatformIO → Install the first plugin

[] Click on Platform>Embedded>Search for Espressif 32 in the input box and select the corresponding firmware installation


【Note】

[] Use the delivered circuit board. Connect the board to the USB and computer without touching anything else. Upload the code. The code will start immediately after downloading and running. Unplug the circuit board and reconnect to the USB. The board of directors cannot do anything.

[] Use the delivered circuit board. Press the start button. When pressing the start button, connect the USB to the computer. Release the start button. Upload the code. The code will not start immediately after downloading. Nothing will happen. Unplug the circuit board and reconnect to the USB. The development board will now guide the code. Connect the motherboard from USB to the computer and connect it to another power source, such as a LiPO battery. The chessboard will start encoding again. This computer is no longer needed.

By performing steps 1 or 2, new code can be loaded onto the circuit board. Both will continue to work.

TAG: Magnetic Encoder Servo Motor 35KG.CM 24V 360° RS485 High Precision And Large Torque RSBL35-24-HS Raspberry Pi CM4 ESP32 S3 Development Board 1.85 inch Round LCD Display 360×360 QMI8658 Sensor / MIC / SD /MP3 Audio /Battery Port LVGL/HMI For Arduino Raspberry Pi 5 Gen3 Raspberry Pi 0.85inch LCD RV1106 MPS2.5G Raspberry Pi 5 PCIe to NVME SSD And 2.5G Ethernet RJ45 HAT RTL8125 2280 2242 2230 Install Espressif IDF Plugin Tutorial User Guide Modbus POE ETH Relay MQTT User Guide Raspberry Pi Starlight Camera IR-CUT IMX462 (A) Sensor 2MP 90 Degree RS232 to Ethernet Raspberry Pi 5 IMX219 Milk-V Duo S UART Serial Console​ Milk V Duo IO Board Tutorial here User Guide UART To CAN Mini Raspberry Pi 5 POE + PCIe to M.2 NVMe SSD Board HAT+ Pi5 2242/2230 Power over Ethernet Raspberry Pi Triple LCD HAT Raspberry Pi RTC WatchDog Raspberry Pi Screen