• sales

    +86-0755-88291180

Lichee-Tang-Primer-20K-FPGA-Unboxing

【Dock ext-board】

】Matters need attention

Here are matters need attention, to avoid spending much time dealing with trouble and fail at last.

[] Enable Core Board

    For 20K Dock kits, it's necessary to enable the core board before using debugger debug the chip, just put the 1 switch on the dip switch down, otherwise LED0 and LED1 are on and core board dose not work.


[] Device not work

    We have inserted the Core Board into Dock ext-board before delivery, but sometimes we need remove the Core board for some reasons, and after reinserting the Core Board into Dock ext-board, they don't work.

    The correct connection steps is to insert the Core board into the ext-board at an Angle roughly as shown in the left figure below. Make sure that the Core board inserted diagonally from above is in uniform contact with the ext-board, which can be judged by the degree of uniformity of the exposed gold finger.


    Then gently press the tilted end, you can hear a sound of the Core board being fixed by the ext-board slot.

If you find it difficult to press the tilted end, you can try to polish both sides of the Core board slightly to eliminate the size error caused by the production process.

Just polish the two sides of the red box in the figure above to reduce the difficulty of inserting. 


[] Hardware version introduction

For Dock ext-board, we can know the version of our board from the mark in the following picture.


From the figure we can know the version of this board is V3708.

Here are their errors.

 -> V3708

LED2 and LED3 are marked wrong, thay should be:

NameCorrect maskWrong mask
LED2N16B14
LED3N14

N16


】Start to use

For Dock ext-board, the following things can be done with default firmware.

  • Press key S0, reset the RGB screen, camera, HDMI signal. And LED3, LED4, LED5 are on.
  • Press key S0 to key S5, the state of LED0, lED1, LED2 changes.
  • Connect OV5640 camera and 4.3 inch RGB screen with Dock ext-board (Make sure power is off while connecting), the screen display the picture captured by camera. If the screen displays not well, try to press key S0, this will synchronize the camera picture and screen content.


Questions

Visit Questions for more solvements


【Lite ext-board】

Hardware version introduction

For Lite ext-board,we can know the version of our board from the mark in the following picture.


From the figure we can know the version of this board is 3710.

Here are their errors.

[] 3710

The mask between R8 and P9 is P8. Refer to the left top of the right picture.

 

】Questions

Visit Questions for more solvements

TAG: Industrial Modbus POE ETH RJ45 To Relay 30CH RTU/Modbus TCP-Ethernet For IOT WiFi Wireless ESP32 DDSM Motor Driver HAT For Direct Drive Servo Hub Motors For Raspberry Pi Raspberry Pi 5 SSD ESP32-S3 USB Dongle 240x280 Raspberry Pi 5 Case DeepSeek ESP32-S3 Voice Chat Robot espHome XiaoZhi Ball DeepsSeek XiaoZhi AI Voice Chat ESP32-S3 1.54 inch LCD Kit N16R8 WROOM-1-N16R8 DevKitC-1 Development Board Pi5 Pure- DeepSeek XiaoZhi AI Voice Chat ESP32-S3 All-in-One-PCB-Kit N16R8 WROOM-1-N16R8 DevKitC-1 Development Board ESP32 2 inch Capacitive TouchScreen LCD Display ST7789 CST816D 240x320 For Arduino/Raspberry Pi/Pico ESP32 S3 LCD Development Board 1.3 inch Display 1.3inch Screen ST7789 240x240 Mini TV SD-Port QST QMI8658 Gyro Sensor LVGL For Arduino 1.14inch LCD Package Kit Raspberry Pi CM4S08032 And Compute Module PoE IO Board Industrial USB TO RS485 2CH Converter FT2232HL Grade Isolated X1002 Raspberry Pi 5 PCIe to M.2 NVMe SSD Adapter Board HAT Pi5 2280 UGV Beast PT Kit AI OpenCV Robot Car MediaPipe For Jetson Orin Arducam ADXL357BEZ LuckFox Pico UART