• sales

    +86-0755-88291180

1.54inch e-Paper (C)

Introduction

152x152, 1.54inch E-Ink display module, three-color, SPI interface

Interfaces

VCC3.3V
GNDGND
DINSPI MOSI
CLKSPI SCK
CSSPI chip select (Low active)
DCData/Command control pin (High for data, and low for command)
RSTExternal reset pin (Low for reset)
BUSYBusy state output pin (Low for busy)


Working principle

Introduction

This product is an E-paper device adopting the image display technology of Microencapsulated Electrophoretic Display, MED. The initial approach is to create tiny spheres, in which the charged color pigments are suspending in the transparent oil and would move depending on the electronic charge. The E-paper screen display patterns by reflecting the ambient light, so it has no background light requirement. Under sunshine, the E-paper screen still has high visibility with a wide viewing angle of 180 degree. It is the ideal choice for E-reading.

Communication protocol



Note: Different from the traditional SPI protocol, the data line from the slave to the master is hidden since the device only has display requirement.

  • CS is slave chip select, when CS is low, the chip is enabled.
  • DC is data/command control pin, when DC = 0, write command, when DC = 1, write data.
  • SCLK is the SPI communication clock.
  • SDIN is the data line from the master to the slave in SPI communication.

SPI communication has data transfer timing, which is combined by CPHA and CPOL.

  1. CPOL determines the level of the serial synchronous clock at idle state. When CPOL = 0, the level is Low. However, CPOL has little effect to the transmission.
  2. CPHA determines whether data is collected at the first clock edge or at the second clock edge of serial synchronous clock; when CPHL = 0, data is collected at the first clock edge.
  • There are 4 SPI communication modes. SPI0 is commonly used, in which CPHL = 0, CPOL = 0.

As you can see from the figure above, data transmission starts at the first falling edge of SCLK, and 8 bits of data are transferred in one clock cycle. In here, SPI0 is in used, and data is transferred by bits, MSB first.


TAG: Arduino IR Thermal Imaging Camera 1.54inch LCD TouchScreen Display 240×240 ST7789S For Arduino /Raspberry Pi /ESP32 /Pico /STM32 Electronic EYE 0.71 inch Round Double LCD Display Dual Screen For Arduino Raspberry Pi ESP32 Pico ST Image-Modulation-Tutorial User Guide ESP32 Drone Development board DIY Flight Controller Open-Source Mini Quadcopter RS485 to RJ45 4 inch e Paper HAT+ E Ink Spectra E6 Full-Color 600x400 Screen Display For Arduino /Raspberry Pi /Jetson Nano /STM32 ESP32-C6 LCD Development Board 1.3 inch Display 1.3inch Screen ST7789 240x240 Mini TV SD-Port QST LVGL For Arduino Luckfox Pico RJ45 Magnetic Encoder Servo Motor 45KG.CM 24V 360° RS485 High Precision And Large Torque ESP32-S31 Mini Development Board based on ESP32-S31NRV16/32 dual-core processor Raspberry Pi 5 User Guide ESP32-S3 Industrial-Grade IOT RS485 CAN Communicator WiFi Bluetooth Raspberry Pi Touch Display 2 Official Original Capacitive TouchScreen 7 inch LCD TFT 720x1280 ESP32-S3 AI Voice Dialogue Robot Mechanical Dog Development Board Toy Tabletop Pet Deepseek Raspberry Pi 10.1 inch DSI LCD TouchScreen Display 800x1280 Also For RK3576/RK3506/ESP32-P4 Capacitive Touchscreen Raspberry Pi LCD display screen 1.3inch ST7789 with Game Button A Raspberry Pi 5 Raspberry Pi Pico 2 RP2350A 1.54inch TouchScreen 1.54 inch LCD Display Development Board 240×240