STM32 ST-LINK/V2 (CN) User Guide

Introduction

User Manual

Resources

Question:

STLINK/V2 does not have a CD-ROM? Why not distribute the CD?

Answer:

Yes, this is ST official original, there is no CD itself. However, we can provide you with a link to download the product information from the web disk. You can look at the pictures of the product introduction, software, etc. to be downloaded from the Internet. The driver is also downloaded from the Internet.

We also don’t know why we don’t have an extra CD to make the operation easier and more convenient for customers. It may not consider these difficulties of users when it launches the product. Not having a CD is very troublesome, sorry, but we can't arrange it, because the original factory does not have it as standard. We stock many sets here, all of which are the same.

You can send an email to the official website and make suggestions.

Question:

Is your ST-LINK/V2 (CN) not original? The product picture I saw on the official website www.ST.com is different from yours.

Answer:

Hello, it should be that you did not read it carefully. Open the PDF corresponding to the official website page. There are 2 places where the version is mentioned. As shown below:

In fact, ST-LINK/V2 is subdivided into 2 versions: ST-LINK/V2 and ST-LINK/V2-ISOL. Our company currently supplies ST-LINK/V2, which guarantees 100% brand new original authenticity.

Question:

When designing the download circuit, do I need to supply power to ST-LINK?

Answer:

It must be powered, that is, at least one of these 2 pins inputs 3.3V from the outside

Question:

When programming STM8, the board cannot input power from the outside, what should I do?

Answer:

Note: This step may burn out the downloader and target board and lose the ST warranty. Please operate with caution!
Note: This step may burn out the downloader and target board and lose the ST warranty. Please operate with caution!
Note: This step may burn out the downloader and target board and lose the ST warranty. Please operate with caution!

The normal download of STM8 is connected to the target board through the SWIM interface, and the target board is connected to an external power supply.

However, some customers do not have external power supply on the target board due to design errors or cost-saving reasons during research and development, and normal ST-LINK cannot be downloaded.

The following two points need to be short-circuited. At this time, the downloader can supply power to the target board (it is best to use a fuse to short-circuit, if there is no fuse, it can be short-circuited directly, but make sure that there is no short-circuit inside the target board!)

Question:

In keil, the program can be downloaded and run normally, but an error similar to the following appears when debugging?

Cannot access Memory
Error while accessing a target resource. The resource is perhaps not available or a wrong access was attempted.
*** error 57: illegal address (0x08000000)

Answer:

Uncheck the Download to Flash option in the Options for Target-"Debug-"Settings-"Debug-"Download Options dialog box.

Question:

When using STLINK-V3SET, the downloader can be recognized by keil software and the chip ID can be read, but the following error is reported?

Answer:

Look at the keil version number, at least 5.25 can be used

Question:

How to download STVP software on ST official website?

Answer:

Open the STVP download link:

http://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/stvp-stm32.html

Find "Get Software" to get the software

Click to agree to the agreement

Fill in your name (pinyin), email address, tick it, click "download" to download, ST will send a link to your mailbox, click the link, and repeat the "first step" to download the software.

To：

Dear Customers, There may be a lag of several hours before we could process your order, depending on the time difference between your location and ours. Sincerely hoping your understanding!

Email(support)

services01@spotpear.com

TAG： USB IR Infrared Thermal Imaging Camera C 45°/88° 160x120 For Phone/PC High Temp Warning/Take Photo /Recording video ESP32 C3 SIM8260G M2 3G/4G/5G/GNSS/GPS Sub-6G PCIe M.2 Moudle For LTE-A/NSA/SA For DFOTA /VoLTE For SIMCOM RP2040-PiZero ESP32 C3 RV1106 Raspberry Pi 5 POE + PCIe to M.2 NVMe SSD Board HAT+ Pi5 2242/2230 Power over Ethernet DC-DC Step-Down Mini voltage Moudle Input 5~36V voltage Output 5V/3.3V 4A Raspberry Pi UGV Rover ROS2 PT AI OpenCV Robot Car MediaPipe Raspberry Pi PICO LoRa ESP32 S3 5 inch LCD Development Board 800x480 TouchScreen Display TVBOX LVGL HMI Sensor CAN RS485 Pi5 Pure-Copper Active Cooler Raspberry Pi 500 (US) refined personal computer.built into a high-quality Keyboard Sipeed NanoKVM Cube KVM HDMI Remote OS Control Manager Install /Power Control /Remote Desktop Server UART Raspberry Pi 12.3 inch DSI MIPI Display TouchScreen LCD 720x1920 Luckfox Lyra Omni3576 RK3576 Raspberry Pi Pico JETSON NANO MINI Expansion Board ESP32 Thermal imaging camera Raspberry Pi USB Global Shutter Camera 1MP OV9281 120fps Black/White 120fps also For Jeston RDK STLINK

ST LINK/V2 (CN) STM32 ST8 Programmers and Debuggers

TAG： ESP32 Drone Development board DIY Flight Controller Open-Source Mini Quadcopter Raspberry Pi ESP32-S3 AI Camera 1.28inch LCD Dual MIC Development Board Display 1.28 inch Voice Interruption Object Recognition 10-in-1 Multifunctional HDMI to TTL Raspberry Pi Autofocus Camera 8MP IMX415 93.5° FOV Distortion-Free ESP32 LVGL Raspberry Pi PCM5122 I2S DAC HIFI Sound Card DAC Audio expansion Board Free-Driver For PI5/PI4/Zero ESP32-S3 1.28inch Round LCD Display TouchScreen Accelerometer Gyroscope Sensor Case Power Manager Module Modbus ESP32 S3 Round 1.5 inch OLED TouchScreen Smart Knob Display Spotpear ESP32-S3 LCD Computer Secondary Screen 2.9 inch Passive NFC e-Paper ink (G) RYBW Display Screen No Need Battery Wireless Power & Data Transfer Cyberpunk LED Matrix Hourglass Gravity Sensor DIY Countdown Timer Clock STEM Educational Soldering Project for Beginners & Adult ESP32-S3 GEEK lilygo Raspberry Pi 3 LCD HAT ESP32-S3 BOX3 For XiaoZhi AI ESP-Claw Desk Pet OpenClaw Smart Home Robot