1.64inch e-Paper / Module (G) User Guide

Feature

Dimension: 1.64 inch
Outline dimension (raw panel): 45.5mm × 36.4mm × 0.91mm
Outline dimension (driver board): 47mm x 38mm
Display dimension: 29.568mm × 29.568mm
Working voltage: 3.3V/5V
Communication interfaces: SPI
Pixel pitch: 0.176 × 0.176mm
Resolution: 168 x 168
Display color: Black, White, Yellow, Red
Gray level: 2
Full refreshing time: 12 s
Refresh Power Consumption: < 57 mW(typ.)
Standby current: <0.01uA(close to0)
Note:
- Refresh time: The refresh time is the experimental results, the actual refresh time will have errors, and the actual effect shall prevail. There will be a flickering effect during the global refresh process, this is a normal phenomenon.
- Power consumption: The power consumption data is the experimental results. The actual power consumption will have a certain error due to the existence of the driver board and the actual use situation. The actual effect shall prevail.

SPI Communication Timing

Since the ink screen only needs to be displayed, the data cable (MISO) sent from the machine and received by the host is hidden here.

CS: Slave chip select, when CS is low, the chip is enabled.
DC: data/command control pin, write command when DC=0; write data when DC=1.
SCLK: SPI communication clock.
SDIN: SPI communication master sends, the slave receives.
Timing: CPHL=0, CPOL=0 (SPI0).

[Remarks] For specific information about SPI, you can search for information online.

E-ink Refresh Principle

Working Principle

This product is an E-paper device adopting the image display technology of Microencapsulated Electrophoretic Display. The basic principle is that charged nanoparticles suspended in a liquid migrate under the action of an electric field. The E-paper screen display patterns by reflecting the ambient light, so it has no background light requirement. Under ambient light, the E-paper screen still has high visibility with a wide viewing angle of 180 degrees. It is the ideal choice for E-reading.

Pixel & Byte

We define the pixels in a monochrome picture, 0 is black and 1 is white.
White：□: Bit 1
Black：■: Bit 0

The dot in the figure is called a pixel. As we know, 1 and 0 are used to define the color, therefore we can use one bit to define the color of one pixel, and 1 byte = 8pixels
For example, If we set the first 8 pixels to black and the last 8 pixels to white, we show it by codes, they will be 16 bit as below:

For computer, the data is saved in MSB format:

So we can use two bytes for 16 pixels.

Precautions

For E-paper displays that support partial refresh, please note that you cannot refresh them with the partial refresh mode all the time. After refreshing partially several times, you need to fully refresh EPD once. Otherwise, the display effect will be abnormal, which cannot be repaired!
It is a normal phenomenon that the three-color EPD will have a certain color difference in different batches. Hence, It is recommended to use the program to clear all the pictures on the EPD and store it facing up. Please clear the screen several times before powering on.
Note that the screen cannot be powered on for a long time. When the screen is not refreshed, please set the screen to sleep mode or power off it. Otherwise, the screen will remain in a high voltage state for a long time, which will damage the e-Paper and cannot be repaired!
When using the e-Paper display, it is recommended that the refresh interval be at least 180s, and refresh at least once every 24 hours. If the e-Paper is not used for a long time, you should use the program to clear the screen before storing it. (Refer to the datasheet for specific storage environment requirements.)
After the screen enters sleep mode, the sent image data will be ignored, and it can be refreshed normally only after initializing again.
Control the 0x3C or 0x50 (refer to the datasheet for details) register to adjust the border color. In the demo, you can adjust the Border Waveform Control register or VCOM AND DATA INTERVAL SETTING to set the border.
If you find that the created image data is displayed incorrectly on the screen, it is recommended to check whether the image size setting is correct, change the width and height settings of the image and try again.
The working voltage of the e-Paper display is 3.3V. If you buy the raw panel and you need to add a level convert circuit for compatibility with 5V voltage. The new version of the driver board (V2.1 and subsequent versions) has added a level processing circuit, which can support both 3.3V and 5V. The old version only supports a 3.3V working environment. You can confirm the version before using it. (The one with the 20-pin chip on the PCB is generally the new version.)
The FPC cable of the screen is relatively fragile, pay attention to bending the cable along the horizontal direction of the screen when using it, and do not bend the cable along the vertical direction of the screen.
The screen of e-Paper is relatively fragile, please try to avoid dropping, bumping, and pressing hard.
We recommend that customers use the sample program provided by us to test with the corresponding development board.

Users Guides of Raspberry Pi

Hardware connection

If the e-Paper you have is the HAT version which has 40pin GPIO, you can directly attach the e-Paper HAT on Raspberry Pi, otherwise, you can connect your e-Paper to Raspberry Pi by 8pins cable provided.

To connect the e-Paper, you can following the table below:

Connect to Raspberry Pi
e-Paper	Raspberry Pi
e-Paper	BCM2835	Board
VCC	3.3V	3.3V
GND	GND	GND
DIN	MOSI	19
CLK	SCLK	23
CS	CE0	24
DC	25	22
RST	17	11
BUSY	24	18

Take the 7.5inch HD e-Paper (B) connected to the e-paper Driver HAT as an example, just plug it directly into the Raspberry Pi:

Enable SPI interface

The communication interface of e-Paper is SPI, to use it, we should firstly enable the SPI interface.

Open terminal of Raspberry Pi, and open the configuration by the following command:

sudo raspi-config

Choose Interfacing Options -> SPI -> Yes

Restart Raspberry Pi

sudo reboot

Install libraries

Note: If you use the Bullseye image, please use "apt" instead of "apt-get" to install libraries, the Bullseye image could only support "ptyhon3".

Open the terminal of Raspberry Pi and run the following commands to install corresponding libraries:

Install BCM2835 libraries:

#Open the Raspberry Pi terminal and run the following command
wget http://www.airspayce.com/mikem/bcm2835/bcm2835-1.71.tar.gz
tar zxvf bcm2835-1.71.tar.gz
cd bcm2835-1.71/
sudo ./configure && sudo make && sudo make check && sudo make install
# For more information, please refer to the official website: http://www.airspayce.com/mikem/bcm2835/

Install WiringPi libraries:

#Open the Raspberry Pi terminal and run the following command
sudo apt-get install wiringpi
#For Raspberry Pi systems after May 2019 (earlier than before, you may not need to execute), you may need to upgrade:
wget https://project-downloads.drogon.net/wiringpi-latest.deb
sudo dpkg -i wiringpi-latest.deb
gpio -v
# Run gpio -v and version 2.52 will appear. If it does not appear, the installation is wrong
#Bullseye branch system use the following command:
git clone https://github.com/WiringPi/WiringPi
cd WiringPi
./build
gpio -v
# Run gpio -v and version 2.60 will appear. If it does not appear, it means that there is an installation error

Install Python2 libraries:

 sudo apt-get update
 sudo apt-get install python-pip
 sudo apt-get install python-pil
 sudo apt-get install python-numpy
 sudo pip install RPi.GPIO
 sudo pip install spidev

Install Python3 libraries:

sudo apt-get update
sudo apt-get install python3-pip
sudo apt-get install python3-pil
sudo apt-get install python3-numpy
sudo pip3 install RPi.GPIO
sudo pip3 install spidev

Download demo codes

Open the Raspberry Pi terminal and execute:
Method 1: Download from Waveshare:

sudo apt-get install p7zip-full
wget  https://www.waveshare.com/w/upload/3/39/E-Paper_code.7z
7z x E-Paper_code.7z -O./e-Paper
cd e-Paper/RaspberryPi_JetsonNano/

Method 2: Use GitHub

git clone https://github.com/waveshare/e-Paper
cd e-Paper/RaspberryPi_JetsonNano/

Examples

C

Open main. c to select the screen of the corresponding size.

cd c
sudo nano examples/main.c

If you are using 2.7inch e-paper, then remove the // in front of the EPD_2IN7_test() function, then press Ctrl+c, press the Y key and Enter to save and exit, as shown in the figure: (The picture may not be updated. Timely, subject to the specific demo).
Supporting types:

1.02inch（128 × 80）：

EPD_1in02d_test()：Example for 1.02inch e-Paper/1.02inch e-Paper Module

1.54inch（1.54inch e-paper c：152 × 152，others：200 × 200）：

EPD_1in54_test()： Example for 1.54inch e-paper V1（Balck/White）: This version was discontinued.
EPD_1in54_V2_test(): Example for 1.54inch e-paper V2（Balck/White): Purchase date later than November 2019 is the V2 version, the current shipping version has the V2 logo on the back.
EPD_1in54b_test()： Example for 1.54inch e-paper B（Black/White/Red). It is currently out of production.
EPD_1in54b_V2_test(): Example for 1.54inch e-Paper B V2 (Black/White/Red). The purchase date later than November 2019 is the V2 version, the current shipping version has the V2 logo on the back;
EPD_1in54c_test()： Example for 1.54inch e-paper C（Black/White/Red）;

1.64inch（168 × 168）

EPD_1in64g_test(): Example for 1.64inch e-paper G (Black/White/Red/Yellow)

2.7inch（264 × 176）

EPD_2in7_test(): Example for 2.7inch e-paper（Black/White）;
EPD_2in7b_test(): Example for 2.7inch e-paper B（Black/White/Red）;
EPD_2in7b_V2_test(): Example for 2.7inch e-paper B V2（Black/White/Red). The purchase date is later than February 2021 is the V2 version, the current shipping version has the V2 logo on the back;

2.9inch (296 × 128)

EPD_2in9_test(): Example for 2.9inch e-paper (Black/White), this version was discontinued.
EPD_2in9_V2_test(): Example for 2.9inch e-paper V2（Black/White）; The purchase date is later than December 2020 is the V2 version, the current shipping version has the V2 logo on the back;
EPD_2in9bc_test(): Example for 2.9inch e-paper B（Balck/White/Red） and 2.9inch e-paper C（Black/White/Yellow）;
EPD_2in9b_V3_test(): Example for 2.9inch e-paper B V3 （Balck/White/Red）; Purchase date later than July 2020 is the V3 version, the current shipping version has the V3 logo on the back;
EPD_2in9d_test(): Example for 2.9inch e-paper D（Black/White）;

2.13inch（2.13inch e-Paper：250 × 122，others：212 × 104）：

EPD_2in13_test(): Example for 2.13inch e-paper V1（Black/White）, this version was discontinued.
EPD_2in13_V2_test(): Example for 2.13inch e-paper V2（Black/White）. The purchase date is later than May 2019, the V2 version is currently discontinued, and the V2 logo is affixed on the back;
EPD_2in13_V3_test(): Example for 2.13inch e-paper V3（Black/White） This is the current version with sticker V3 on the backside (2020-07-29)；
EPD_2in13bc_test()：Example for 2.13inch e-paper B（Black/White/Red）and 2.13inch e-paper C（Blackj/White/Yellow）;
EPD_2in13b_V3_test()：Example for 2.13inch e-paper B V3（Black/White/Red）Purchase date later than April 2020 is the V3 version, the current shipping version has the V3 logo on the back;
EPD_2in13d_test()： Example for 2.13inch e-paper D（Black/White）;

2.66inch (152 × 296)

EPD_2in66_test(): Example for 2.66inch e-Paper (Black/White);
EPD_2in66b_test(): Example for 2.66inch e-Paper B (Black/White/Red);

3inch (400 × 168)

EPD_3in0g_test(): Example for 3inch e-Paper G(Black/White/Red/Yellow);

3.52inch (360 × 240)

EPD_3in52_test(): Example for 3.52inch e-Paper (Black/White);

3.7inch (280 × 480)

EPD_3in7_test(): Example for 3.7inch e-Paper(Black/White);

4.01inch (640 × 400)

EPD_4in01_test(): Example for the 4.01inch e-Paper HAT (F) (Black/White/Green/Blue/Red/Yellow/Orange);

4.2inch（400 × 300）

EPD_4in2_test()： Example for 4.2inch e-paper（Black/White）；
EPD_4in2bc_test()： Example for 4.2inch e-paper B（Black/White/Red）；
EPD_4in2b_V2_test()： Example for 4.2inch e-paper B V2（Black/White/Red）. The purchase date is later than November 2020, it is the V2 version, and the current shipping version has the V2 logo on the back;

5.65inch (600 × 558)

EPD_5in65f_test(): Example for for 5.65inch e-Paper F (Black/White/Green/Blue/Red/Yellow/Orange);

5.83inch（600 × 448）：

EPD_5in83_test()： Example for 5.83inch e-paper（Black/White）, It is currently out of production.
EPD_5in83_V2_test()： Example for 5.83inch e-paper V2（Black/White）, The purchase date is later than December 2020 is the V2 version, the current shipping version, with the V2 logo on the back.
EPD_5in83bc_test()： Example for 5.83inch e-paper B（Black/White/Red）and 5.83inch e-paper C（Black/White/Yellow）;
EPD_5in83b_V2_test()： Example for 5.83inch e-paper B V2（Black/White/Red). The purchase date is later than August 2020 for the V2 version, the current shipping version, with the V2 logo on the back.

7.3inch (800 × 480)

epd_7in3g_test.py: Example for 7inch3 e-paper G (Black/White/Red/Yellow).

7.5inch（V1：640 × 384， V2：800 × 480）：

EPD_7in5bc_V2_test()： Example for 7.5inch e-paper B V2（Black/White/Red）; The purchase date is later than 2019-12-07 is the V2 version, with the V2 logo on the back; the purchase date is later than March 2021 is the V3 version, the current 7.5inch e-paper B shipping version, with the V3 logo on the back, the same use this program;

7.5inch (880 × 528)

EPD_7in5_HD_test(): Example for 7.5inch e-Paper HD (Black/White);
EPD_7in5b_HD_test(): Example for 7.5inch e-Paper B HD (Black/White/Red);

*Note: The above time is for reference only, please refer to the screen logo for the specific version.

Recompile, the compilation process may take a few seconds

Return to the c directory and run the following command
make clean
make
sudo ./epd

Python

PS: The system of the Bullseye branch only supports Python3.

Enter the folder of python code.

cd python/examples
ls -al

Run the responding example.

sudo python epd_xxx_test.py
sudo python3 epd_xxx_test.py

Supporting types:

1.02inch（128×80）：

epd_1in02_test.py：Example for 1.02inch e-Paper/1.02inch e-Paper Module

1.54inch（1.54inch e-paper c：152×152，others：200×200）：

epd_1in54_test.py： Example for 1.54inch e-paper V1（Balck/White）: This version is stopped production which can be bought before 2019-11-22；
epd_1in54_V2_test.py： Example for 1.54inch e-paper V2（Balck/White): This is the current version which can be bought now (2020-07-29). The e-Paper has V2 sticker on the backside.
epd_1in54b_test.py： Example for 1.54inch e-paper B（Black/White/Red). It is currently out of production.
epd_1in54b_V2_test.py： Example for 1.54inch e-paper B V2 (Black/White/Red). The purchase date is later than April 2020 is the V2 version, the current shipping version has the V2 logo on the back;
epd_1in54c_test.py： Example for 1.54inch e-paper C（Black/White/Red).

1.64inch（168 × 168）

epd_1in64g_test.py: Example for 1.64inch e-paper G (Black/White/Red/Yellow)

2.7inch（264×176）：

epd_2in7_test.py： Example for 2.7inch e-paper（Black/White）;
epd_2in7b_test.py： Example for 2.7inch e-paper B（Black/White/Red）;
epd_2in7b_V2_test.py： Example for 2.7inch e-paper B V2 (Black/White/Red). The purchase date is later than February 2021 is the V2 version, the current shipping version has the V2 logo on the back;

2.9inch（296×128）：

epd_2in9_test.py: Example for 2.9inch e-paper（Black/White）; It is currently out of production.
epd_2in9_V2_test.py: Example for 2.9inch e-paper V2（Black/White）; The purchase date is later than December 2020 is the V2 version, the current shipping version, with the V2 logo on the back.
epd_2in9bc_test.py： Example for 2.9inch e-paper B（Balck/White/Red） and 2.9inch e-paper C（Black/White/Yellow）;
epd_2in9b_V3_test.py： Example for 2.9inch e-paper B V3（Balck/White/Red; The purchase date later than July 2020 is the V3 version, the current shipping version has the V3 logo on the back;
epd_2in9d_test.py： Example for 2.9inch e-paper D（Black/White）;

2.13inch（2.13inch e-Paper：250×122，others：212×104）：

epd_2in13_test.py： Example for 2.13inch e-paper V1（Black/White）, this version is stopped production and it can be bought before 019-05-15;
epd_2in13_V2_test.py： Example for 2.13inch e-paper V2（Black/White） This is the current version with sticker V2 on the backside (2020-07-29)；
epd_2in13_V3_test.py: Example for 2.13inch e-paper V3（Black/White）, The purchase date later than February 2022 is the V3 version, the current shipping version, with the V3 logo on the back.
epd_2in13bc_test.py： Example for 2.13inch e-paper B（Black/White/Red）and 2.13inch e-paper C（Black/White/Yellow）;
epd_2in13b_V3_test.py： Example for 2.13inch e-paper B V3（Black/White/Red）
epd_2in13d_test.py： Example for 2.13inch e-paper D（Black/White）;

2.66inch (152 x 296)

epd_2in66_test.py: Example for 2.66inch e-Paper (Black/White);
epd_2in66b_test.py: Example for 2.66inch e-Paoer (Black/White/Red);

3inch (400 × 168)

EPD_3in0g_test.py: Example for 3inch e-Paper G(Black/White/Red/Yellow);

3.52inch (360 × 240)

EPD_3in52_test.py: Example for 3.52inch e-Paper (Black/White);

3.7inch (280 x 480)

epd_3in7_test.py: Example for 3.7inch e-Paper (Black/White);

4.01inch (640x400)

epd_4in01f_test.py: Example for 4.01inch e-Paper (Seven-color);

4.2inch（400×300）

epd_4in2_test.py： Example for 4.2inch e-paper（Black/White）；
epd_4in2bc_test.py： Example for 4.2inch e-paper B（Black/White/Red）；
epd_4in2b_V2_test.py： Example for 4.2inch e-paper B V2（Black/White/Red). The purchase date is later than November 2020, it is the V2 version, and the current shipping version has the V2 logo on the back;

5.65inch (600x558)

epd_5in65f_test.py: Example for 5.65inch e-Paper F (Seven-color);

5.83inch（600×448）：

epd_5in83_test.py： Example for 5.83inch e-paper（Black/White). It is currently out of production.
epd_5in83_V2_test.py： Example for 5.83inch e-paper V2（Black/White); The purchase date is later than December 2020 is the V2 version, the current shipping version has the V2 logo on the back;
epd_5in83bc_test.py： Example for 5.83inch e-paper B（Black/White/Red）and 5.83inch e-paper C（Black/White/Yellow）;
epd_5in83b_V2_test.py： Example for 5.83inch e-paper B V2（Black/White/Red). The purchase date is later than August 2020 is the V2 version, the current shipping version has the V2 logo on the back;

7.3inch (400 × 168)

epd_7in3g_test.py: Example for 7inch3 e-paper G (Black/White/Red/Yellow).

7.5inch（V1：640×384， V2：800×480）：

epd_7in5_test.py： Example for 7.5inch e-paper（Black/White）, this version is stopped production and it can be bought before 2019-12-07；
epd_7in5_V2_test.py： Example for 7.5inch e-paper V2（Black/White）, This is the current version with V2 sticker on the backside (2020-07-29)
epd_7in5bc_test.py： Example for 7.5inch e-paper B（Black/White/Red）and 7.5inch e-paper C（Black/White/Yellow）, 7.5inch e-paper B V1 version is stopped production and it can be bought before 2019-12-07;
epd_7in5b_V2_test.py： Example for 7.5inch e-paper B V2（Black/White/Red）. The purchase date later than 2019-12-07 is the V2 version, with the V2 logo on the back; the purchase date later than March 2021 is the V3 version, the current 7.5inch e-paper B shipping version, with the V3 logo on the back, the same use this program.

7.5inch (HD 880 x 528)

epd_7in5_HD_test.py: Example for 7.5inch e-Paper HD (Black/White);
epd_7in5b_HD_test.py: Example for 7.5inch e-Paper B HD (Black/White/Red);

Note: The above time is for reference only, please refer to the screen logo for the specific version.
Just run the program corresponding to the screen, the program supports python2/3, take 1.54 V2 as an example.

# python2
sudo python2.7 epd_1in54_V2_test.py
# python3
sudo python3 epd_1in54_V2_test.py

Codes Description(API)

The libraries for Raspberry Pi and Jetson Nano are same. Examples contain three parts, hardware interface, EPD driver and the GUI functions.

C

Hardware interface

We have carried out the underlying package. As the hardware platform is different, the internal is various. If you need to know the internal, you can go to the corresponding directory.
You can see many definitions in DEV_Config.c(.h), in the directory: RaspberryPi_JetsonNano\c\lib\Config.
C language uses two ways to drive: BCM2835 library, and WiringPi library. The BCM2835 library is used by default. If you need to use the WiringPi library to drive, you can open RaspberryPi_JetsonNano\c\Makefile and modify lines 13-14.

Data type

#define UBYTE   uint8_t
#define UWORD   uint16_t
#define UDOUBLE uint32_t

Init and Exit

void DEV_Module_Init(void);
void DEV_Module_Exit(void);

Note: The Init() and Exit() functions are used to configure GPIOs. EPD enters sleep mode after Exit() function is used, and the consumption of e-Paper should be 0 in sleep mode if the PCB is Rev2.1 version.

GPIO Read/Write

void DEV_Digital_Write(UWORD Pin, UBYTE Value);
UBYTE DEV_Digital_Read(UWORD Pin);

SPI transmits data.

void DEV_SPI_WriteByte(UBYTE Value);

EPD Driver

The driver file is saved under RaspberryPi&JetsonNano\c\lib\e-Paper.

Open .h to see the following functions

EPD initialization: please use it when the EPD starts to work or exits the sleep mode.

//1.54inch e-Paper, 1.54inch e-Paper V2, 2.13inch e-Paper, 2.13inch e-Paper V2, 2.13inch e-Paper (D), 2.9inch e-Paper, 2.9inch e-Paper (D )
void EPD_xxx_Init(UBYTE Mode); // Mode = 0 full refresh initialization, Mode = 1 partial refresh initialization
//other models
void EPD_xxx_Init(void);

Where xxx represents the model. If it is 2.13D, the full screen initialization is EPD_2IN13D_Init(0), the partial refresh initialization EPD_2IN13D_Init(1); if it is 1.54 V2, then EPD_1IN54_V2_Init(); if it is 7.5B, it is EPD_7IN5BC_Init(). Although the display colors are different, the driver code of 7.5B and 7.5C is the same.

Clear the screen, and refresh the ink screen to white.

void EPD_xxx_Clear(void);

Where xxx represents the ink screen model. If it is 2.13D, then it is EPD_2IN9D_Clear(); if it is 7.5B, it is EPD_7IN5_Clear(). Although the display colors are different, the driver code of 7.5B and 7.5C is the same.

Transfer a frame of picture data and open the display.

//Black and white two-color ink screen
void EPD_xxx_Display(UBYTE *Image);
//Black and white red or black and white yellow ink screen
void EPD_xxx_Display(const UBYTE *blackimage, const UBYTE *ryimage);

Note that the following are special cases:

//For 2.13inch e-paper (D), 2.9inch e-paper (D) two flexible screens, partial refresh
void EPD_2IN13D_DisplayPart(UBYTE *Image);
void EPD_2IN9D_DisplayPart(UBYTE *Image);

//For 1.54inch e-paper V2 and 2.13inch e-paper V2, due to the upgrade of the control chip, for a partial refresh, it is necessary to call EPD_xxx_DisplayPartBaseImage to display the static background image, that is, to perform partial refresh based on this image, and then call the dynamic EPD_xxx_DisplayPart ()

void EPD_1IN54_V2_DisplayPartBaseImage(UBYTE *Image);
void EPD_1IN54_V2_DisplayPart(UBYTE *Image);
void EPD_2IN13_V2_DisplayPart(UBYTE *Image);
void EPD_2IN13_V2_DisplayPartBaseImage(UBYTE *Image);

Enter sleep mode

void EPD_xxx_Sleep(void);

Note that after entering sleep mode, there are only two ways to work again: the first is a hardware reset, and the second is to call the initialization function again.
Where xxx represents the ink screen model. If it is 2.13D, then it is EPD_2IN13D_Sleep(); if it is 7.5B, it is EPD_7IN5BC_Sleep(). Although the display colors are different, the driver code of 7.5B and 7.5C is the same.

GUI functions

GUI files can be found in RaspberryPi&JetsonNano\c\lib\GUI\GUI_Paint.c(.h) directory.

The fonts can be found in the RaspberryPi&JetsonNano\c\lib\Fonts directory.

Create an image buffer

void Paint_NewImage(UBYTE *image, UWORD Width, UWORD Height, UWORD Rotate, UWORD Color)

Image: the Image buffer
Width: width of the image
Height: Height of the image
Rotate: Rotate angle
Color: Color of the image

Select image buffer

void Paint_SelectImage(UBYTE *image)

The image buffer is a pointer of the image buffer's first address.

Rotate image: This function should be used after Paint_SelectImage().

void Paint_SetRotate(UWORD Rotate)

Rotate: The angle rotated. It should be ROTATE_0, ROTATE_90, ROTATE_180, ROTATE_270.
Note: For different orientations, the position of the first pixel is different, here we take 1.54inch as an example.

Mirroring

void Paint_SetMirroring(UBYTE mirror)

mirror: The type of mirroring. (MIRROR_NONE, MIRROR_HORIZONTAL、MIRROR_VERTICAL、MIRROR_ORIGIN)

Set Pixel: This function is used to set the position and types of the pixel

void Paint_SetPixel(UWORD Xpoint, UWORD Ypoint, UWORD Color)

Xpoint: The x-axis coordination of pixel
Ypoint: The y-axis coordination of pixel
Color: The color of the pixel

Clear: This function is used to clear the e-Paper

void Paint_Clear(UWORD Color)

Color: The color of the display

Clear window: This function is used to clear a partial area

void Paint_ClearWindows(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color)

Xstart: The x-axis coordination of the start point
Ystart: The y-axis coordination of the start point
Xend: The x-axis coordination of the end point
Yend: The y-axis coordination of the end point
Color: The color of the windows

Draw point

This function is used to draw point.

void Paint_DrawPoint(UWORD Xpoint, UWORD Ypoint, UWORD Color, DOT_PIXEL Dot_Pixel, DOT_STYLE Dot_Style)

Xpoint: The x-axis coordination of point
Ypoint: The y-axis coordination of point
Dot_Pixel: The size of the point

 	 	 typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  , 	 	// 3 X 3
 	 	 	 DOT_PIXEL_4X4  , 	 	// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;

Dot_Style: The style of the point

 	 	typedef enum {
 	 	   DOT_FILL_AROUND  = 1,		
 	 	   DOT_FILL_RIGHTUP,
 	 	} DOT_STYLE;

Draw Line

void Paint_DrawLine(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color, LINE_STYLE Line_Style , LINE_STYLE Line_Style)

This function is used to draw a line

Xstart: The start x-axis coordination of the line
Ystart: The start y-axis coordination of the line
Xend: The end x-axis coordination of the line
Yend: The end y-axis coordination of the line
Line_width: The width of the line

 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;

Line_style: The style of the line

 	 	typedef enum {
 	 	 	 LINE_STYLE_SOLID = 0,
 	 	 	 LINE_STYLE_DOTTED,
 	 	} LINE_STYLE;

Draw rectangle

Draw a rectangle from (Xstart, Ystart) to (Xend, Yend).

void Paint_DrawRectangle(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color, DOT_PIXEL Line_width, DRAW_FILL Draw_Fill)

Xstart: Start coordinate of X-axes of the rectangle
Ystart: Start coordinate of Y-axes of the rectangle
Xend: End coordinate of X-end of the rectangle
Yend: End coordinate of Y-end of the rectangle
Color: color of the rectangle
Line_width: The width of edges, 8 sides are available;

 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;

Draw_Fill: set the rectangle as full or empty.

typedef enum {
 	DRAW_FILL_EMPTY = 0,
 	DRAW_FILL_FULL,
} DRAW_FILL;

Draw circle: Draw a circle: In the image cache, with (X_Center Y_Center) as the center, draw a circle with a radius of Radius, you can choose the color, the width of the line, and whether to fill the inside of the circle

void Paint_DrawCircle(UWORD X_Center, UWORD Y_Center, UWORD Radius, UWORD Color, DOT_PIXEL Line_width, DRAW_FILL Draw_Fill)
parameter:
 X_Center: X coordinate of the center of the circle
 Y_Center: Y coordinate of the center of the circle
 Radius: the radius of the circle
 Color: fill color
 Line_width: the width of the arc, providing 8 default widths
 typedef enum {
                 DOT_PIXEL_1X1 = 1, // 1 x 1
                 DOT_PIXEL_2X2 , // 2 X 2
                 DOT_PIXEL_3X3 , // 3 X 3
                 DOT_PIXEL_4X4 , // 4 X 4
                 DOT_PIXEL_5X5 , // 5 X 5
                 DOT_PIXEL_6X6 , // 6 X 6
                 DOT_PIXEL_7X7 , // 7 X 7
                 DOT_PIXEL_8X8 , // 8 X 8
 } DOT_PIXEL;
 Draw_Fill: Fill, whether to fill the inside of the circle
          typedef enum {
                        DRAW_FILL_EMPTY = 0,
                        DRAW_FILL_FULL,
 } DRAW_FILL;

Draw character (ASCII)

Set(Xstart Ystart) as the left-top point, and draw an ASCII character.

void Paint_DrawChar(UWORD Xstart, UWORD Ystart, const char Ascii_Char, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameter:

Xstart: X coordinate of the left-top pixel of character;
Ystart: Y coordinate of the left-top pixel of character;
Ascii_Char：Ascii character;
Font: 5 fonts are available;
font12：7*12
font16：11*16
font20：14*20
font24：17*24
Color_Foreground: color of character;
Color_Background: color of background;

Draw String

Set point (Xstart Ystart) as the left-top pixel, draw a string.

void Paint_DrawString_EN(UWORD Xstart, UWORD Ystart, const char * pString, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameters:

Xstart: X coordinate of left-top pixel of characters;
Ystart: Y coordinate of left-top pixel of characters;
pString：Pointer of string
Font: 5 fonts are available:
font8：5*8
font12：7*12
font16：11*16
font20：14*20
font24：17*24
Color_Foreground: color of string
Color_Background: color of the background

Draw Chinese characters

this function is used to draw Chinese fonts based ON GB2312 fonts.

void Paint_DrawString_CN(UWORD Xstart, UWORD Ystart, const char * pString, cFONT* font, UWORD Color_Foreground, UWORD Color_Background)

Parameters:

Xstart: Coordinate of left-top pixel of characters;
Ystart: Coordinate of left-top pixel of characters;
pString：Pointer of string;
Font: GB2312 fonts：
font12CN：11*21(ascii)，16*21 (Chinese)
font24CN：24*41(ascii)，32*41 (Chinese)
Color_Foreground: color of string
Color_Background: color of the background

Draw number

Draw a string of numbers, (Xstart, Ystart) is the left-top pixel.

void Paint_DrawNum(UWORD Xpoint, UWORD Ypoint, int32_t Number, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameter:

Xstart: X coordinate of left-top pixel;
Ystart: Y coordicate of left-to pixel;
Nummber: the numbers displayed. the numbers are saved in int format, the maximum is 2147483647;
Font: 5 fonts are available：
font8：5*8
font12：7*12
font16：11*16
font20：14*20
font24：17*24
Color_Foreground: the color of the font;
Color_Background: the color of background;

Draw image

Send image data of BMP file to buffer

void Paint_DrawBitMap(const unsigned char* image_buffer)

Parameters:

image_buffer: address of image data in the buffer.

Read local bmp picture and write it to buffer.

Linux platforms like Jetson Nano and Raspberry Pi support directly operate bmp pictures. Raspberry Pi & Jetson Nano：RaspberryPi&JetsonNano\c\lib\GUI\GUI_BMPfile.c(.h).

UBYTE GUI_ReadBmp(const char *path, UWORD Xstart, UWORD Ystart)

Parameters:

path：The path of BMP pictures
Xstart: X coordination of left-top of picture, default 0;
Ystart: Y coordination of left-top of picture, default 0;

Testing Code

The first three chapters introduce the classic Linux three-layer code structure, here is a little explanation of the user test code.
For Raspberry Pi and Jetson Nano, in the directory: RaspberryPi_JetsonNano\c\examples, for all test codes, multiple shields can be made in main.c in this directory;
If you need to run the 7.5inch e-paper test program, you need to remove the 42-line shield.

//EPD_5in65f_test();

EPD_5in65f_test();

Then compile it again and run.

make clean
make
sudo ./epd

Python

For Jetson Nano\Raspberry Pi, based on python2.7 and python3.
For python, its calls are not as complicated as C.
Raspberry Pi and Jetson Nano: RaspberryPi_JetsonNano\python\lib\

Bottom Interface

The epdconfig.py file package the underlying interface.

Initialize module and exit handle：

def module_init()
def module_exit()

Note:
1. The functions are used to set GPIP before and after driving e-Paper.
2. If the board you have is printed with Rev2.1, the module enters low-ultra mode after Module_Exit(). (as we test, the current is about 0 in this mode);

GPIO Read/Write：

def  digital_write(pin, value)
def  digital_read(pin)

SPI Write data:

def spi_writebyte(data)

Driver Interface

epdxxx.py (xxx means size, if it is 2.13inch e-paper, it is epd2in13.py, and so on)

Initialize e-paper: this function should be used at the beginning. It can also be used to wake up e-Paper from Sleep mode.

#For 2.13inch e-Paper、2.9inch e-Paper
def init(self, update) #  Choose lut_full_update or lut_partial_update
# Other types
def init(self)

Clear e-paper: This function is used to clear e-Paper to white;

def Clear(self)
def Clear(self, color) # Some types of e-Paper should use this function to clear screen

Convert image to arrays

def getbuffer(self, image)

Transmit one frame of image data and display

#For two-color e-paper
def display(self, image)

#Because that controllers of 2.13inch e-paper are updated, when partial refresh, they should first use displayPartBaseImage() to display static background, then use displayPart() to dynamaticlly display.
def displayPartBaseImage(self, image)
def displayPart(self, image)

Enter sleep mode

def sleep(self)

Testing Function

epd_xxx_test.py (xxx means dimension)python examples are saved in the directory：
Raspberry Pi and Jetson Nano：RaspberryPi&JetsonNano\python\examples\

If the python installed in your OS is python2, you should run examples like the below：

sudo python epd_2in13_V2_test.py

If it is python3, the commands should be:

sudo python3 epd_2in13-V2_test.py

Orientation

To rotate the display, you can use transpose function like blackimage = blackimage.transpose(Image.ROTATE_270):

blackimage = blackimage.transpose(Image.ROTATE_270) 
redimage = redimage.transpose(Image.ROTATE_270)
#Support ROTATE_90, ROTATE_180, ROTATE_270

The rotation effect, taking 1.54B as an example, is 0°, 90°, 180°, 270° in sequence

GUI

Python has a powerful PIL library, which can be used directly to drawing figures. Here we use it for drawing.

Install the library firstly.

sudo apt-get install python3-pil

Import the library.

from PIL import Image,ImageDraw,ImageFont

Image: library; ImageDraw: drawing function; ImageFont: fonts

Set image buffer for drawing.

image = Image.new('1', (epd.width, epd.height), 255)  # 255: clear the frame

The first parameter is the depth of color, 1 means 2 grayscale. The second parameter is a tuple of image size. The third parameter is the color of the image, 0 is black and 255 is white.

Create an image object.

draw = ImageDraw.Draw(image)

Draw rectangle

draw.rectangle((0, 10, 200, 34), fill = 0)

The first parameter is a tuple of coordination. 0, 10 is the top-left point of the rectangle, and 200, 34) is the right-bottom point. fille = 0 set the fill color to black.

Draw line

draw.line((16, 60, 56, 60), fill = 0)

The first parameter is a type of coordination, 16, 60 is the beginning point, and 200, 34 is the endpoint. fill=0 set the line to black.

Draw circle

draw.arc((90, 60, 150, 120), 0, 360, fill = 0)

This function is used to draw a encircle of a square. The first parameter is a tuple of coordination of the square. the degree of the circle is 0 to 360 °, fille=0 set the circle to black.
If the figure is not square according to the coordination, you will get an ellipse.

Besides the arc function, you can also use the chord function for drawing a solid circle.

draw.chord((90, 130, 150, 190), 0, 360, fill = 0)

The first parameter is the coordination of the enclosing rectangle. The second and third parameters are the beginning and end degrees of the circle. The fourth parameter is the fill color of the circle.

Character

You can directly import the ImageFont model for drawing characters:

font = ImageFont.truetype(os.path.join(picdir, 'Font.ttc'), 24)

You can use the fonts of Windows or other fonts which is in ttc format.

To draw English character, you can directly use the fonts; for Chinese characters, you need to add a symbol u:

draw.text((8, 12), 'hello world', font = font, fill = 255)
draw.text((8, 36), u'微雪电子', font = font, fill = 0)

The first parameter is a tuple of coordination of character, the second parameter is the font and las one is set the color.

Read local picture

image = Image.open(os.path.join(picdir, 'lin54.bmp'))

The parameter is the path of picture.

Other functions.

For more information about the PIL library, you can search online.

User Guides of Jetson Nano

Hardware connection

Because the 40PIN GPIO of Jetson Nano are compatible with Raspberry Pi's and the Jetson.GPIO libraries are compatible with RPi.GPIO, therefore we use the same connection as Raspberry Pi.

To connect the e-Paper, you can following the table below.

Jetson Nano Connection
e-Paper	Jetson Nano Developer Kit
e-Paper	BCM2835	Board
VCC	3.3V	3.3V
GND	GND	GND
DIN	10(SPI0_MOSI)	19
CLK	11(SPI0_SCK	23
CS	8(SPI0_CS0)	24
DC	25	22
RST	17	11
BUSY	24	18

Software Setting

Install Libraries

Open the terminal of Jetson Nano and run the following commands to install corresponding libraries:

sudo apt-get update
sudo apt-get install python3-pip
sudo pip3 install Jetson.GPIO
sudo groupadd -f -r gpio
sudo usermod -a -G gpio your_user_name
sudo cp /opt/nvidia/jetson-gpio/etc/99-gpio.rules /etc/udev/rules.d/
sudo udevadm control --reload-rules && sudo udevadm trigger

Install I2C libraries

sudo apt-get install python3-smbus

Install PIL libraries

sudo apt-get install python3-pil
sudo apt-get install python3-numpy

Download Testing Program

Open a linux terminal and execute:
Method 1: Using the GitHub repository

sudo git clone https://github.com/waveshare/e-Paper

Run the Test Program

Please execute the following commands under RaspberryPi_JetsonNano, otherwise, the directory will not be indexed.

C

Modify the main.c file for corresponding e-Paper.

cd c
sudo nano examples/main.c

If you are using 2.7inch e-paper, then remove the // in front of the EPD_2IN7_test() function, then press ctrl+c, then press Y and press Enter to save and exit, as shown:
Supporting Types
1.02inch（128×80）
EPD_1in02d_test()：Example for 1.02inch e-Paper/1.02inch e-Paper Module

1.54inch（1.54inch e-paper c：152×152，others：200×200）
EPD_1in54_test()： Example for 1.54inch e-paper V1（Balck/White）: This version is stopped production which can be bought before 2019-11-22；
EPD_1in54_V2_test(): Example for 1.54inch e-paper V2（Balck/White): This is the current version that can be bought now (2020-07-29). The e-Paper has V2 sticker on the backside.
EPD_1in54b_test()： Example for 1.54inch e-paper B（Black/White/Red). It is currently out of production.
EPD_1in54b_V2_test(): Example for 1.54inch e-Paper B V2 (Black/White/Red). The purchase date later than November 2019 is the V2 version, the current shipping version has the V2 logo on the back;
EPD_1in54c_test()： Example for 1.54inch e-paper C（Black/White/Red）;

1.64inch（168 × 168）
EPD_1in64g_test(): Example for 1.64inch e-paper G (Black/White/Red/Yellow)

2.7inch（264×176）
EPD_2in7_test(): Example for 2.7inch e-paper（Black/White）;
EPD_2in7b_test(): Example for 2.7inch e-paper B（Black/White/Red）;
EPD_2in7b_V2_test(): Example for 2.7inch e-paper B V2（Black/White/Red）;

2.9inch（296×128）
EPD_2in9_test(): Example for 2.9inch e-paper (Black/White), this version is stopped production.
EPD_2in9_V2_test(): Example for 2.9inch e-paper V2（Black/White）; The purchase date is later than December 2020 is the V2 version, the current shipping version has the V2 logo on the back;
EPD_2in9bc_test(): Example for 2.9inch e-paper B（Balck/White/Red） and 2.9inch e-paper C（Black/White/Yellow）;
EPD_2in9b_V3_test(): Example for 2.9inch e-paper B V3 （Balck/White/Red）; Purchase date later than July 2020 is the V3 version, the current shipping version has the V3 logo on the back;
EPD_2in9d_test(): Example for 2.9inch e-paper D（Black/White）;

2.13inch（2.13inch e-Paper：250×122，others：212×104）：
EPD_2in13_test(): Example for 2.13inch e-paper V1（Black/White）, this version is stopped production and it can be bought before 019-05-15;
EPD_2in13_V2_test(): Example for 2.13inch e-paper V2（Black/White） This is the current version with sticker V2 on the backside (2020-07-29)；
EPD_2in13_V3_test(): Example for 2.13inch e-paper V3（Black/White） This is the current version with sticker V3 on the backside (2020-07-29)；
EPD_2in13bc_test()：Example for 2.13inch e-paper B（Black/White/Red）and 2.13inch e-paper C（Blackj/White/Yellow）;
EPD_2in13b_V3_test()：Example for 2.13inch e-paper B V3（Black/White/Red）Purchase date later than April 2020 is the V3 version, the current shipping version has the V3 logo on the back;
EPD_2in13d_test()： Example for 2.13inch e-paper D（Black/White）;

2.66inch (152 x 296)
EPD_2in66_test(): Example for 2.66inch e-Paper (Black/White);
EPD_2in66b_test(): Example for 2.66inch e-Paper B (Black/White/Red);

3inch (400 × 168)
EPD_3in0g_test(): Example for 3inch e-Paper G(Black/White/Red/Yellow);

3.52inch (360 × 240)
EPD_3in52_test(): Example for 3.52inch e-Paper (Black/White);

3.7inch (280 x 480)
EPD_3in7_test(): Example for 3.7inch e-Paper(Black/White);

4.01inch (640x400)
EPD_4in01_test(): Example for the 4.01inch e-Paper HAT (F) (Black/White/Green/Blue/Red/Yellow/Orange);

4.2inch（400×300）
EPD_4in2_test()： Example for 4.2inch e-paper（Black/White）；
EPD_4in2bc_test()： Example for 4.2inch e-paper B（Black/White/Red）；
EPD_4in2b_V2_test()： Example for 4.2inch e-paper B V2（Black/White/Red）. The purchase date is later than November 2020, it is the V2 version, and the current shipping version has the V2 logo on the back;
5.65inch (600x448)
EPD_5in65f_test(): Example for for 5.65inch e-Paper F (Black/White/Green/Blue/Red/Yellow/Orange);

5.83inch（600×448）
EPD_5in83_test()： Example for 5.83inch e-paper（Black/White）, It is currently out of production.
EPD_5in83_V2_test()： Example for 5.83inch e-paper V2（Black/White）, The purchase date is later than December 2020 is the V2 version, the current shipping version, with the V2 logo on the back.
EPD_5in83bc_test()： Example for 5.83inch e-paper B（Black/White/Red）and 5.83inch e-paper C（Black/White/Yellow）;
EPD_5in83b_V2_test()： Example for 5.83inch e-paper B V2（Black/White/Red). The purchase date is later than August 2020 for the V2 version, the current shipping version, with the V2 logo on the back.

7.5inch（V1：640×384， V2：800×480）
EPD_7in5_test()： Example for 7.5inch e-paper（Black/White）. The purchase date is earlier than 2019-12-07 as the V1 version, which is currently discontinued.
EPD_7in5bc_test()： For example for 7.5inch e-paper B（Black/White/Red）and 7.5inch e-paper C（Black/White/Yellow）, The purchase date later than 2019-12-07 is the V2 version, and the current shipping version has the V2 logo on the back;
EPD_7in5_V2_test()： Example for 7.5inch e-paper V2（Black/White）. The purchase date of 7.5inch e-paper B is earlier than 2019-12-07, which is the V1 version, which is currently discontinued, and 7.5inch e-paper C is normally available.
EPD_7in5bc_V2_test()： Example for 7.5inch e-paper B V2（Black/White/Red）; The purchase date is later than 2019-12-07 is the V2 version, with the V2 logo on the back; the purchase date is later than March 2021 is the V3 version, the current 7.5inch e-paper B shipping version, with the V3 logo on the back, the same use this program;

7.5inch(HD880 x 528)
EPD_7in5_HD_test(): Example for 7.5inch e-Paper HD (Black/White);
EPD_7in5b_HD_test(): Example for 7.5inch e-Paper B HD (Black/White/Red);

*Note: The above time is for reference only, please refer to the screen logo for the specific version.

Recompile, the compilation process may take a few seconds.

Return to the c directory and run the following command
make clean
make JETSON
sudo ./epd

Python

Enter the python program directory and run the command ls -al.

cd python/examples
ls -al

Support Types
1.02inch（128×80）
epd_1in02_test.py：Example for 1.02inch e-Paper/1.02inch e-Paper Module.

1.54inch（1.54inch e-paper c：152×152，others：200×200）
epd_1in54_test.py： Example for 1.54inch e-paper V1（Balck/White). This version is stopped production which can be bought before 2019-11-22；
epd_1in54_V2_test.py： Example for 1.54inch e-paper V2（Balck/White): This is the current version which can be bought now (2020-07-29). The e-Paper has V2 sticker on the backside.
epd_1in54b_test.py： Example for 1.54inch e-paper B（Black/White/Red). It is currently out of production.
epd_1in54b_V2_test.py： Example for 1.54inch e-paper B V2 (Black/White/Red). The purchase date is later than April 2020 is the V2 version, the current shipping version has the V2 logo on the back;
epd_1in54c_test.py： Example for 1.54inch e-paper C（Black/White/Red).

2.7inch（264×176）
epd_2in7_test.py： Example for 2.7inch e-paper（Black/White）;
epd_2in7b_test.py： Example for 2.7inch e-paper B（Black/White/Red）;
epd_2in7b_V2_test.py： Example for 2.7inch e-paper B V2 (Black/White/Red). The purchase date is later than February 2021 is the V2 version, the current shipping version has the V2 logo on the back;

2.9inch（296×128）
epd_2in9_test.py: Example for 2.9inch e-paper（Black/White）; It is currently out of production.
epd_2in9_V2_test.py: Example for 2.9inch e-paper V2（Black/White）; The purchase date is later than December 2020 is the V2 version, the current shipping version, with the V2 logo on the back.
epd_2in9bc_test.py： Example for 2.9inch e-paper B（Balck/White/Red） and 2.9inch e-paper C（Black/White/Yellow）;
epd_2in9b_V3_test.py： Example for 2.9inch e-paper B V3（Balck/White/Red). The purchase date later than July 2020 is the V3 version, the current shipping version has the V3 logo on the back;
epd_2in9d_test.py： Example for 2.9inch e-paper D（Black/White）;

2.13inch（2.13inch e-Paper：250×122，others：212×104）
epd_2in13_test.py： Example for 2.13inch e-paper V1（Black/White）, this version is stopped production and it can be bought before 019-05-15;
epd_2in13_V2_test.py： Example for 2.13inch e-paper V2（Black/White） This is the current version with sticker V2 on the backside (2020-07-29)；
epd_2in13_V3_test.py: Example for 2.13inch e-paper V3（Black/White）, The purchase date later than February 2022 is the V3 version, the current shipping version, with the V3 logo on the back.
epd_2in13bc_test.py： Example for 2.13inch e-paper B（Black/White/Red）and 2.13inch e-paper C（Black/White/Yellow）;
epd_2in13b_V3_test.py： Example for 2.13inch e-paper B V3（Black/White/Red）
epd_2in13d_test.py： Example for 2.13inch e-paper D（Black/White）;

2.66inch (152 x 296)
epd_2in66_test.py: Example for 2.66inch e-Paper (Black/White);
epd_2in66b_test.py: Example for 2.66inch e-Paoer (Black/White/Red);

3inch (400 × 168)
EPD_3in0g_test.py: Example for 3inch e-Paper G(Black/White/Red/Yellow);

3.52inch (360 × 240)
EPD_3in52_test.py: Example for 3.52inch e-Paper (Black/White);

3.7inch (280 x 480)
epd_3in7_test.py: Example for 3.7inch e-Paper (Black/White);

4.01inch (640x400)
epd_4in01f_test.py: Example for 4.01inch e-Paper (Seven-color);

4.2inch（400×300）
epd_4in2_test.py： Example for 4.2inch e-paper（Black/White）；
epd_4in2bc_test.py： Example for 4.2inch e-paper B（Black/White/Red）；
epd_4in2b_V2_test.py： Example for 4.2inch e-paper B V2（Black/White/Red). The purchase date is later than November 2020, it is the V2 version, and the current shipping version has the V2 logo on the back;

5.65inch (600x448)
epd_5in65f_test.py: Example for 5.65inch e-Paper F (Seven-color);

5.83inch（600×448）
epd_5in83_test.py： Example for 5.83inch e-paper（Black/White). It is currently out of production.
epd_5in83_V2_test.py： Example for 5.83inch e-paper V2（Black/White); The purchase date is later than December 2020 is the V2 version, the current shipping version has the V2 logo on the back;
epd_5in83bc_test.py： Example for 5.83inch e-paper B（Black/White/Red）and 5.83inch e-paper C（Black/White/Yellow）;
epd_5in83b_V2_test.py： Example for 5.83inch e-paper B V2（Black/White/Red). The purchase date is later than August 2020 is the V2 version, the current shipping version has the V2 logo on the back;

7.5inch（V1：640×384， V2：800×480）
epd_7in5_test.py： Example for 7.5inch e-paper（Black/White）, this version is stopped production and it can be bought before 2019-12-07；
epd_7in5_V2_test.py： Example for 7.5inch e-paper V2（Black/White）, This is the current version with V2 sticker on the backside (2020-07-29)
epd_7in5bc_test.py： Example for 7.5inch e-paper B（Black/White/Red）and 7.5inch e-paper C（Black/White/Yellow）, 7.5inch e-paper B V1 version is stopped production and it can be bought before 2019-12-07;
epd_7in5b_V2_test.py： Example for 7.5inch e-paper B V2（Black/White/Red）. The purchase date later than 2019-12-07 is the V2 version, with the V2 logo on the back; the purchase date later than March 2021 is the V3 version, the current 7.5inch e-paper B shipping version, with the V3 logo on the back, the same use this program.

7.5inch (HD 880 x 528)
epd_7in5_HD_test.py: Example for 7.5inch e-Paper HD (Black/White);
epd_7in5b_HD_test.py: Example for 7.5inch e-Paper B HD (Black/White/Red);

*Note: The above time is for reference only, please refer to the screen logo for the specific version

Just run the program corresponding to the screen, the program supports python2/3, take 1.54 V2 as an example

# python2
sudo python2.7 epd_1in54_V2_test.py
# python3
sudo python3 epd_1in54_V2_test.py

Description of codes (API)

The libraries for Raspberry Pi and Jetson Nano are the same. Examples contain three parts, hardware interface, EPD driver, and the GUI functions.

C

Hardware interface

Two libraries are used by C example, WiringPi, and BCM2835. The codes use wiringPi by default, if you want to use BCM2835, you can modify the RaspberryPi&JetsonNano\c\Makefile file, modify lines 13 and 14. Change it as below:

Data type

#define UBYTE   uint8_t
#define UWORD   uint16_t
#define UDOUBLE uint32_t

Init and Exit

void DEV_Module_Init(void);
void DEV_Module_Exit(void);

Note: The Init() and Exit() function are used to configure GPIOs . EPD enter sleep mode after Exit() function is used, and the consumption of e-Paper should be 0 in sleep mode if the PCB is Rev2.1 version.

GPIO Read/Write

void DEV_Digital_Write(UWORD Pin, UBYTE Value);
UBYTE DEV_Digital_Read(UWORD Pin);

SPI transmit data

void DEV_SPI_WriteByte(UBYTE Value);

EPD

e-paper driver code file, in the directory: RaspberryPi_JetsonNano\c\lib\e-Paper.
As shown below:

Open .h to see the following functions.

After the initialization, called when the screen starts working and after exiting sleep mode.

//1.54inch e-Paper, 1.54inch e-Paper V2, 2.13inch e-Paper, 2.13inch e-Paper V2, 2.13inch e-Paper (D), 2.9inch e-Paper, 2.9inch e-Paper (D )
void EPD_xxx_Init(UBYTE Mode); // Mode = 0 global refresh initialization, Mode = 1 local refresh initialization
//other models
void EPD_xxx_Init(void);

Where xxx represents the model. If it is 2.13D, the full screen initialization is EPD_2IN13D_Init(0), the partial refresh initialization EPD_2IN13D_Init(1); if it is 1.54 V2, then EPD_1IN54_V2_Init(); if it is 7.5B, it is EPD_7IN5BC_Init(), because 7.5B and 7.5C are common The driver code, but the color displayed is different.

Clear the screen, brush the ink screen to white

void EPD_xxx_Clear(void);

Where xxx represents the ink screen model. If it is 2.13D, then it is EPD_2IN9D_Clear(); if it is 7.5B, it is EPD_7IN5_Clear(), because 7.5B and 7.5C share the driver code, but the color displayed is different.

Transfer a frame of picture data and open the display.

//Black and white two-color ink screen
void EPD_xxx_Display(UBYTE *Image);
//Black and white red or black and white yellow ink screen
void EPD_xxx_Display(const UBYTE *blackimage, const UBYTE *ryimage);

Note that the following are special cases:

//For 2.13inch e-paper (D), 2.9inch e-paper (D) two flexible screens, partial refresh
void EPD_2IN13D_DisplayPart(UBYTE *Image);
void EPD_2IN9D_DisplayPart(UBYTE *Image);

void EPD_1IN54_V2_DisplayPartBaseImage(UBYTE *Image);
void EPD_1IN54_V2_DisplayPart(UBYTE *Image);
void EPD_2IN13_V2_DisplayPart(UBYTE *Image);
void EPD_2IN13_V2_DisplayPartBaseImage(UBYTE *Image);

Enter sleep mode

void EPD_xxx_Sleep(void);

Note that after entering sleep mode, there are only two ways to work again: the first is a hardware reset, and the second is to call the initialization function again.
Where xxx represents the ink screen model. If it is 2.13D, then it is EPD_2IN13D_Sleep(); if it is 7.5B, it is EPD_7IN5BC_Sleep(), because 7.5B and 7.5C share the driver code, but the color displayed is different.

GUI Functions

GUI files can be found in RaspberryPi&JetsonNano\c\lib\GUI\GUI_Paint.c(.h) directory

The fonts can be found in RaspberryPi&JetsonNano\c\lib\Fonts directory

Create an image buffer

void Paint_NewImage(UBYTE *image, UWORD Width, UWORD Height, UWORD Rotate, UWORD Color)

Image: the Image buffer
Width: width of the image
Height: Height of the image
Rotate: Rotate angle
Color: Color of the image

Select image buffer

void Paint_SelectImage(UBYTE *image)

The image buffer, it is a pointer of image buffer's first address

Rotate image: This function should be used after Paint_SelectImage()

void Paint_SetRotate(UWORD Rotate)

Rotate: The angle rotated. It should be ROTATE_0, ROTATE_90, ROTATE_180, ROTATE_270
Note: For different orientation, the position of the first pixel is different, here we take 1.54inch as example

Mirroring

void Paint_SetMirroring(UBYTE mirror)

mirror: The type of mirroring. (MIRROR_NONE, MIRROR_HORIZONTAL、MIRROR_VERTICAL、MIRROR_ORIGIN)

Set Pixel: This function is used to set the position and types of the pixel

void Paint_SetPixel(UWORD Xpoint, UWORD Ypoint, UWORD Color)

Xpoint: The x-axis coordination of pixel
Ypoint: The y-axis coordination of pixel
Color: The color of the pixel

Clear: This function is used to clear the e-Paper

void Paint_Clear(UWORD Color)

Color: The color of the display

Clear window: This function is used to clear a partial area

void Paint_ClearWindows(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color)

Xstart: The x-axis coordination of the start point
Ystart: The y-axis coordination of the start point
Xend: The x-axis coordination of the end point
Yend: The y-axis coordination of the end point
Color: The color of the windows

Draw point

This function is used to draw points.

void Paint_DrawPoint(UWORD Xpoint, UWORD Ypoint, UWORD Color, DOT_PIXEL Dot_Pixel, DOT_STYLE Dot_Style)

Xpoint: The x-axis coordination of point
Ypoint: The y-axis coordination of point
Dot_Pixel: The size of the point

 	 	 typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  , 	 	// 3 X 3
 	 	 	 DOT_PIXEL_4X4  , 	 	// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;

Dot_Style: The style of the point

 	 	typedef enum {
 	 	   DOT_FILL_AROUND  = 1,		
 	 	   DOT_FILL_RIGHTUP,
 	 	} DOT_STYLE;

Drawn Line

void Paint_DrawLine(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color, LINE_STYLE Line_Style , LINE_STYLE Line_Style)

This function is used to draw a line

Xstart: The start x-axis coordination of the line
Ystart: The start y-axis coordination of the line
Xend: The end x-axis coordination of the line
Yend: The end y-axis coordination of the line
Line_width: The width of the line

 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;

Line_style: The style of the line

 	 	typedef enum {
 	 	 	 LINE_STYLE_SOLID = 0,
 	 	 	 LINE_STYLE_DOTTED,
 	 	} LINE_STYLE;

Draw rectangle

Draw a rectangle from (Xstart, Ystart) to (Xend, Yend).

void Paint_DrawRectangle(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color, DOT_PIXEL Line_width, DRAW_FILL Draw_Fill)

Xstart: Start coordinate of X-axes of the rectangle
Ystart: Start coordinate of Y-axes of the rectangle
Xend: End coordinate of X-end of the rectangle
Yend: End coordinate of Y-end of the rectangle
Color: color of the rectangle
Line_width: The width of edges, 8 sides are available;

 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;

Draw_Fill: set the rectangle full or empty.

typedef enum {
 	DRAW_FILL_EMPTY = 0,
 	DRAW_FILL_FULL,
} DRAW_FILL;

Draw a circle: In the image cache, with (X_Center Y_Center) as the center, draw a circle with a radius of Radius, you can choose the color, the width of the line, whether to fill the inside of the circle

void Paint_DrawCircle(UWORD X_Center, UWORD Y_Center, UWORD Radius, UWORD Color, DOT_PIXEL Line_width, DRAW_FILL Draw_Fill)
parameter:
          X_Center: X coordinate of the center of the circle
          Y_Center: Y coordinate of the center of the circle
          Radius: the radius of the circle
          Color: fill color
          Line_width: the width of the arc, providing 8 default widths
                       typedef enum {
                                      DOT_PIXEL_1X1 = 1, // 1 x 1
                                      DOT_PIXEL_2X2 , // 2 X 2
                                      DOT_PIXEL_3X3 , // 3 X 3
                                      DOT_PIXEL_4X4 , // 4 X 4
                                      DOT_PIXEL_5X5 , // 5 X 5
                                      DOT_PIXEL_6X6 , // 6 X 6
                                      DOT_PIXEL_7X7 , // 7 X 7
                                      DOT_PIXEL_8X8 , // 8 X 8
 } DOT_PIXEL;
 Draw_Fill: Fill, whether to fill the inside of the circle
            typedef enum {
                          DRAW_FILL_EMPTY = 0,
                          DRAW_FILL_FULL,
 } DRAW_FILL;

Draw character (ASCII)

Set(Xstart Ystart) as letf-top point, draw a ASCII character.

void Paint_DrawChar(UWORD Xstart, UWORD Ystart, const char Ascii_Char, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameter:

Xstart: X coordinate of the left-top pixel of character;
Ystart: Y coordinate of the left-top pixel of character;
Ascii_Char：Ascii character;
Font: 5 fonts are available;
font12：7*12
font16：11*16
font20：14*20
font24：17*24
Color_Foreground: color of character;
Color_Background: color of background;

Draw String

Set point (Xstart Ystart) as the left-top pixel, draw a string.

void Paint_DrawString_EN(UWORD Xstart, UWORD Ystart, const char * pString, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameters:

Xstart: X coordinate of left-top pixel of characters;
Ystart: Y coordinate of left-top pixel of characters;
pString：Pointer of string
Font: 5 fonts are available:
font8：5*8
font12：7*12
font16：11*16
font20：14*20
font24：17*24
Color_Foreground: color of string
Color_Background: color of the background

Draw Chinese characters

this function is used to draw Chinese fonts based ON GB2312 fonts.

void Paint_DrawString_CN(UWORD Xstart, UWORD Ystart, const char * pString, cFONT* font, UWORD Color_Foreground, UWORD Color_Background)

Parameters:

Xstart: Coordinate of left-top pixel of characters;
Ystart: Coordinate of left-top pixel of characters;
pString：Pointer of string;
Font: GB2312 fonts：
font12CN：11*21(ascii)，16*21 (Chinese)
font24CN：24*41(ascii)，32*41 (Chinese)
Color_Foreground: color of string
Color_Background: color of the background

Draw number

Draw a string of numbers, (Xstart, Ystart) is the left-top pixel.

void Paint_DrawNum(UWORD Xpoint, UWORD Ypoint, int32_t Nummber, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameter:

Xstart: X coordinate of left-top pixel;
Ystart: Y coordicate of left-to pixel;
Nummber: the numbers displayed. the numbers are saved in int format, the maximum is 2147483647;
Font: 5 fonts are available：
font8：5*8
font12：7*12
font16：11*16
font20：14*20
font24：17*24
Color_Foreground: color of font;
Color_Background: color of background;

Draw image

Send image data of BMP file to buffer

void Paint_DrawBitMap(const unsigned char* image_buffer)

Parameters:

image_buffer: adrress of image data in buffer

Read local bmp picture and write it to buffer

Linux platform like Jetson Nano and Raspberry Pi support to directly operate bmp pictures Raspberry Pi & Jetson Nano：RaspberryPi&JetsonNano\c\lib\GUI\GUI_BMPfile.c(.h)

UBYTE GUI_ReadBmp(const char *path, UWORD Xstart, UWORD Ystart)

Parameters:

path：The path of BMP pictures
Xstart: X coordination of left-top of picture, default 0;
Ystart: Y coordination of left-top of picture, default 0;

Testing Code

The first three chapters introduce the classic linux three-layer code structure, here is a little explanation of the user test code
For Raspberry Pi and Jetson Nano, in the directory: RaspberryPi_JetsonNano\c\examples, for all test codes, multiple shields can be made in main.c in this directory;
If you need to run the 7.5inch e-paper test program, you need to remove the 42 line shield

// EPD_7in5_test();

change to

EPD_7in5_test();

Re-execute in linux command mode as follows:

make clean
make
sudo ./epd

Python

For Jetson Nano\Raspberry Pi, based on python2.7 and python3
python is easy to use than c codes
Raspberry Pi and Jetson Nano：RaspberryPi&JetsonNano\python\lib\

Bottom Interface

The epdconfig.py file in the underlying interface

Initialize module and exit handle：

def module_init()
def module_exit()

Note:
1. The functions are used to set GPIP before and after driving e-Paper
2. If the board you have is printed with Rev2.1, the module enter low-ultra mode after Module_Exit(). (as we test, the current is about 0 in this mode);

GPIO Read/Write：

def  digital_write(pin, value)
def  digital_read(pin)

SPI Write data:

def spi_writebyte(data)

Driver Interface

epdxxx.py (xxx means size, if it is 2.13inch e-paper, it is epd2in13.py, and so on)

Initialize e-paper: this function should be used at the beginning. It can also be used to wake up e-Paper from Sleep mode.

#For 2.13inch e-Paper、2.9inch e-Paper
def init(self, update) #  Choose lut_full_update or lut_partial_update
#Other type
def init(self)

Clear e-paper: This function is used to clear e-Paper to white;

def Clear(self)
def Clear(self, color) # Some types of e-Paper should use this function to clear screen

Convert image to arrays

def getbuffer(self, image)

Transmit one frame of image data and display

#For two-color e-paper
def display(self, image)

#Because that controllers of 2.13inch e-paper are updated, when partial refresh, they should first use displayPartBaseImage() to display static background, then use displayPart() to dynamaticlly display.
def displayPartBaseImage(self, image)
def displayPart(self, image)

Enter sleep mode

def sleep(self)

Testing Function

epd_xxx_test.py (xxx means size, if it is 2.13inch e-paper, it is epd_2in13_test.py, and so on)
python is in the following directory:
Raspberry Pi and Jetson Nano: RaspberryPi_JetsonNano\python\examples\

If your python version is python2, and you need to run the 7.5inch e-paper test program, re-execute it in the linux command mode as follows:

sudo python epd_7in5_test.py

If your python version is python3, and you need to run the 7.5inch e-paper test program, re-execute it in the linux command mode as follows:

sudo python3 epd_7in5_test.py

Orientation

To rotate the display, you can use transpose function like blackimage = blackimage.transpose(Image.ROTATE_270):

blackimage = blackimage.transpose(Image.ROTATE_270) 
redimage = redimage.transpose(Image.ROTATE_270)
#Support ROTATE_90, ROTATE_180, ROTATE_270

GUI

Python has a powerful PIL library, which can be used directly to draw figures. Here we use it for drawing.

Install the library firstly

sudo apt-get install python3-pil

Import the library

from PIL import Image,ImageDraw,ImageFont

Image: library; ImageDraw: drawing function; ImageFont: fonts

Set image buffer for drawing.

image = Image.new('1', (epd.width, epd.height), 255)  # 255: clear the frame

The first parameter is the depth of color, 1 means 2 grayscale. The second parameter is a tuple of image size. The third parameter is the color of the image, 0 is black and 255 is white.

Create an image object.

draw = ImageDraw.Draw(image)

Draw rectangle

draw.rectangle((0, 10, 200, 34), fill = 0)

The first parameter is a tuple of coordination. 0, 10 is the top-left point of the rectangle, 200, 34) is the right-bottom point. fille = 0 set the fill color to black.

Draw line

draw.line((16, 60, 56, 60), fill = 0)

The first parameter is a type of coordination, 16, 60 is the beginning point, and 200, 34 is the endpoint. fill=0 set the line to black

Draw circle

draw.arc((90, 60, 150, 120), 0, 360, fill = 0)

Besides the arc function, you can also use the chord function for drawing a solid circle.

draw.chord((90, 130, 150, 190), 0, 360, fill = 0)

Character

You can directly import ImageFont model for drawing characters:

font = ImageFont.truetype(os.path.join(picdir, 'Font.ttc'), 24)

You can use the fonts of Windows or other fonts which is in ttc format.

To draw English characters, you can directly use the fonts; for Chinese characters, you need to add a symbol u:

draw.text((8, 12), 'hello world', font = font, fill = 255)
draw.text((8, 36), u'微雪电子', font = font, fill = 0)

The first parameter is a tuple of 2 elements, with (8, 12) as the left vertex, fill is the font color, and the first sentence fill=255, so it seems that it will not be displayed. The second sentence shows 微雪电子.

Read local picture

image = Image.open(os.path.join(picdir, 'lin54.bmp'))

The parameter is the path of picture.

Other functions.

For more information about the PIL library, you can search online.

User Guides of STM32

Hardware connection

The demo codes we provided are based on STM32F103ZET6, the connection table is also based on STM32F103ZET6, if you want to use other chip, you need to port the codes and change the connection according to actual situation.

Connect to STM32F103ZET
e-Paper	STM32
Vcc	3.3V
GND	GND
DIN	PA7
CLK	PA5
CS	PA4
DC	PA2
RST	PA1
BUSY	PA3

If the STM32 board you have is STM32F103RB, you can refer to the guides of E-Paper Shield

Software settings

The codes are based on HAL library. Download the codes and the project files are saved under the STM32\STM32-F103ZET6\MDK-ARM directory.

Modify main.c， define the line according to the e-paper type and re-compile project and download.

Supporting types

1.02inch（128 × 80）：

EPD_1in02d_test()：Example for 1.02inch e-Paper/1.02inch e-Paper Module

1.54inch（1.54inch e-paper c：152 × 152，others：200 × 200）：

EPD_1in54_test()： Example for 1.54inch e-paper V1（Balck/White）: This version is stopped production which can be bought before 2019-11-22；
EPD_1in54_V2_test(): Example for 1.54inch e-paper V2（Balck/White): This is the current version that can be bought now (2020-07-29). The e-Paper has V2 sticker on the backside.
EPD_1in54b_test()： Example for 1.54inch e-paper B（Black/White/Red). It is currently out of production.
EPD_1in54b_V2_test(): Example for 1.54inch e-Paper B V2 (Black/White/Red). The purchase date later than November 2019 is the V2 version, the current shipping version has the V2 logo on the back;
EPD_1in54c_test()： Example for 1.54inch e-paper C（Black/White/Red）;

1.64inch（168 × 168）

EPD_1in64g_test(): Example for 1.64inch e-paper G (Black/White/Red/Yellow)

2.7inch（264 × 176）

2.9inch (296 × 128)

EPD_2in9_test(): Example for 2.9inch e-paper (Black/White), this version is stopped production.
EPD_2in9_V2_test(): Example for 2.9inch e-paper V2（Black/White）; The purchase date is later than December 2020 is the V2 version, the current shipping version has the V2 logo on the back;
EPD_2in9bc_test(): Example for 2.9inch e-paper B（Balck/White/Red） and 2.9inch e-paper C（Black/White/Yellow）;
EPD_2in9b_V3_test(): Example for 2.9inch e-paper B V3 （Balck/White/Red）; Purchase date later than July 2020 is the V3 version, the current shipping version has the V3 logo on the back;
EPD_2in9d_test(): Example for 2.9inch e-paper D（Black/White）;

2.13inch（2.13inch e-Paper：250 × 122，others：212 × 104）：

EPD_2in13_test(): Example for 2.13inch e-paper V1（Black/White）, this version is stopped production and it can be bought before 019-05-15;
EPD_2in13_V2_test(): Example for 2.13inch e-paper V2（Black/White） This is the current version with sticker V2 on the backside (2020-07-29)；
EPD_2in13_V3_test(): Example for 2.13inch e-paper V3（Black/White） This is the current version with sticker V3 on the backside (2020-07-29)；
EPD_2in13bc_test()：Example for 2.13inch e-paper B（Black/White/Red）and 2.13inch e-paper C（Blackj/White/Yellow）;
EPD_2in13b_V3_test()：Example for 2.13inch e-paper B V3（Black/White/Red）Purchase date later than April 2020 is the V3 version, the current shipping version has the V3 logo on the back;
EPD_2in13d_test()： Example for 2.13inch e-paper D（Black/White）;

2.66inch (152 × 296)

EPD_2in66_test(): Example for 2.66inch e-Paper (Black/White);
EPD_2in66b_test(): Example for 2.66inch e-Paper B (Black/White/Red);

3inch (400 × 168)

EPD_3in0g_test(): Example for 3inch e-Paper G(Black/White/Red/Yellow);

3.52inch (360 × 240)

EPD_3in52_test(): Example for 3.52inch e-Paper (Black/White);

3.7inch (280 × 480)

EPD_3in7_test(): Example for 3.7inch e-Paper(Black/White);

4.01inch (640 × 400)

EPD_4in01_test(): Example for the 4.01inch e-Paper HAT (F) (Black/White/Green/Blue/Red/Yellow/Orange);

4.2inch（400 × 300）

5.65inch (600 × 448)

EPD_5in65f_test(): Example for for 5.65inch e-Paper F (Black/White/Green/Blue/Red/Yellow/Orange);

5.83inch（600 × 448）：

7.5inch（V1：640 × 384， V2：800 × 480）：

EPD_7in5_test()： Example for 7.5inch e-paper（Black/White）. The purchase date is earlier than 2019-12-07 as the V1 version, which is currently discontinued.
EPD_7in5bc_test()： For example for 7.5inch e-paper B（Black/White/Red）and 7.5inch e-paper C（Black/White/Yellow）, The purchase date later than 2019-12-07 is the V2 version, and the current shipping version has the V2 logo on the back;
EPD_7in5_V2_test()： Example for 7.5inch e-paper V2（Black/White）. The purchase date of 7.5inch e-paper B is earlier than 2019-12-07, which is the V1 version, which is currently discontinued, and 7.5inch e-paper C is normally available.
EPD_7in5bc_V2_test()： Example for 7.5inch e-paper B V2（Black/White/Red）; The purchase date is later than 2019-12-07 is the V2 version, with the V2 logo on the back; the purchase date is later than March 2021 is the V3 version, the current 7.5inch e-paper B shipping version, with the V3 logo on the back, the same use this program;

7.3inch (400 × 168)

epd_7in3g_test.py: Example for 7inch3 e-paper G (Black/White/Red/Yellow).

7.5inch (880 × 528)

EPD_7in5_HD_test(): Example for 7.5inch e-Paper HD (Black/White);
EPD_7in5b_HD_test(): Example for 7.5inch e-Paper B HD (Black/White/Red);
Note: The above time is for reference only, please refer to the screen logo for the specific version
For example, 1.54inch e-Paper Module. Open the epd1in54 folder and run the epd1in54.ino file.
Open the program, select the development board model Arduino UNO

Codes description

Bottom hardware interface

We package the bottom for different hardware platforms.
You can check the DEV_Config.c(.h) file which is located in \STM32\STM32-F103ZET6\User\Config

Data type:

#define UBYTE   uint8_t
#define UWORD   uint16_t
#define UDOUBLE uint32_t

Module initialized and exit:

void DEV_Module_Init(void);
void DEV_Module_Exit(void);

Note: 1.The functions are used to set GPIP before and after driving e-Paper.
2..If the board you have is printed with Rev2.1, the module enters low-ultra mode after DEV_Module_Exit(). (as we test, the current is about 0 in this mode);

GPIO Read/Write：

void DEV_Digital_Write(UWORD Pin, UBYTE Value);
UBYTE DEV_Digital_Read(UWORD Pin);

SPI Write data

void DEV_SPI_WriteByte(UBYTE Value);

Middle EPD driver

The epd driver are saved in: STM32\STM32-F103ZET6\User\e-Paper

Open .h file, functions are declared here

Initialization: It should be used to initialize e-Paper or wakeup e-Paper from sleep mode.

//1.54inch e-Paper、1.54inch e-Paper V2、2.13inch e-Paper、2.13inch e-Paper  V2、2.13inch e-Paper (D)、2.9inch e-Paper、2.9inch e-Paper (D)
void EPD_xxx_Init(UBYTE Mode); //ode = 0 Initialize full refresh; Mode = 1 Initialize partial refresh 
//Other type
void EPD_xxx_Init(void);

xxx is the type of e-paper

Clear display: This function is used to clear the e-paper to white

void EPD_xxx_Clear(void);

xxx is the type of e-Paper.

Transmit a frame of image and display

//Black/White e-Paper
void EPD_xxx_Display(UBYTE *Image);

Because controllers of 1.54inch e-paper V2 and 2.13inch e-paper V2 were updated, you need to use EPD_xxx_DisplayPartBaseImage to display static image and ten use EPD_xxx_displayPart() to dymatic display when partial refreshing.
void EPD_2IN13_V2_DisplayPart(UBYTE *Image);
void EPD_2IN13_V2_DisplayPartBaseImage(UBYTE *Image);

Enter sleep mode

void EPD_xxx_Sleep(void);

Note, You should hardware reset or use initialize function to wake up e-Paper from sleep mode.
xxx is the type of e-Paper

Application function

Basic drawing functions are provided here. You can find they in:\STM32\STM32-F103ZET6\User\GUI\GUI_Paint.c(.h)

The fonts are saved in the directory:\STM32\STM32-F103ZET6\User\Fonts

Create a new image buffer: This function is used to create a new image with width, height, Rotate degree and its color.

void Paint_NewImage(UBYTE *image, UWORD Width, UWORD Height, UWORD Rotate, UWORD Color)
Parameter:
 	image: The buffer of the image, this is a pointer of buffer address;
 	Width: width of the image;
 	Height: Height of the image;
 	Rotate: Rotate degree;
 	Color: Initial color of the image;

Select image buffer: this function is used to select the image buffer. You can create multiple image buffers with the last function, then select the buffer for every image.

void Paint_SelectImage(UBYTE *image)
Parameter:
 	image: The name of image buffer, it is a pointer of buffer address;

Set display orientation: This function is used to set the rotate degree, it is generally be used after Paint_SelectImage(). You can set the rotate degree to 0、90、180、270 degree.

void Paint_SetRotate(UWORD Rotate)
Parameter:
 	Rotate: Rotate degree, you can choose ROTATE_0、ROTATE_90、ROTATE_180、ROTATE_270 which stands for 0、90、180、270 degree repetitively.

Image mirroring: This function is used to mirror image.

void Paint_SetMirroring(UBYTE mirror)
Parameter:
 	mirror: You can set it to MIRROR_NONE、MIRROR_HORIZONTAL、MIRROR_VERTICAL、MIRROR_ORIGIN

Set pixel: this function is used to set the position and color of pixels in the buffer. This is the basic function of GUI.

void Paint_SetPixel(UWORD Xpoint, UWORD Ypoint, UWORD Color)
Parameter:
 	Xpoint: X-axes in the buffer;
 	Ypoint: Y-axes in buffer;
 	Color: color

Clear: This function is used to clear the screen to certain color.

void Paint_Clear(UWORD Color)
Parameter:
 	Color:

Clear windows: this function is used to clear a window. It is generally used for time display.

void Paint_ClearWindows(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color)
Parameter:
 	Xstart: Start coordinate of X-axes of the window;
 	Ystart: Start coordinate of Y-axes of the window;
 	Xend: End coordinate of X-axes of the window;
 	Yend: End coordinate of Y-axes of the window;
 	Color:

Draw point: Draw a point on the position （Xpoint, Ypoint）in buffer

void Paint_DrawPoint(UWORD Xpoint, UWORD Ypoint, UWORD Color, DOT_PIXEL Dot_Pixel, DOT_STYLE Dot_Style)
Parameter:
 	Xpoint: X coordinate of point;
 	Ypoint: Y coordinate of point;
 	Color: color of point;
 	Dot_Pixel: the size of point, there are 8 sizes available;
 	 	 typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  , 	 	// 3 X 3
 	 	 	 DOT_PIXEL_4X4  , 	 	// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;
 	Dot_Style: style of point. 
 	 	typedef enum {
 	 	   DOT_FILL_AROUND  = 1,		
 	 	   DOT_FILL_RIGHTUP,
 	 	} DOT_STYLE;

Draw line: draw a line for (Xstart, Ystart) to (Xend, Yend)

void Paint_DrawLine(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color, LINE_STYLE Line_Style , LINE_STYLE Line_Style)
Parameter:
 	Xstart: Start coordinate of X-axes of line;
 	Ystart: Start coordinate of Y-axes of line;
 	Xend: End coordinate of X-axes of line;
 	Yend: End coordinate of Y-axes of line
 	Color:
 	Line_width: the width of line, 8 sizes are avalilable;
 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;
 	 Line_Style: Style of the line;
 	 	typedef enum {
 	 	 	 LINE_STYLE_SOLID = 0,
 	 	 	 LINE_STYLE_DOTTED,
 	 	} LINE_STYLE;

Draw rectangle: Draw a rectangle from (Xstart, Ystart) to (Xend, Yend).

void Paint_DrawRectangle(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color, DOT_PIXEL Line_width, DRAW_FILL Draw_Fill)
Parameter:
 	Xstart: Start coordinate of X-axes of rectangle
 	Ystart: Start coordinate of Y-axes of rectangle
 	Xend: End coordinate of X-end of rectangle
 	Yend: End coordinate of Y-end of rectangle
 	Color: color of rectangle
 	Line_width: The width of edges, 8 sides are available;
 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;
 	Draw_Fill: set the rectangle full or empty.
 	 	typedef enum {
 	 	 	 DRAW_FILL_EMPTY = 0,
 	 	 	 DRAW_FILL_FULL,
 	 	} DRAW_FILL;

Draw circle:Draw a circle, use (X_Center Y_Center) as center;

void Paint_DrawCircle(UWORD X_Center, UWORD Y_Center, UWORD Radius, UWORD Color, DOT_PIXEL Line_width, DRAW_FILL Draw_Fill)
Parameter:
 	X_Center: X coordinate of center
 	Y_Center: Y coordinate of center
 	Radius：Radius of circle
 	Color: color of circle
 	Line_width: width of circle, 8 sizes are avalilable
 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;
 	Draw_Fill: style of circle
 	 	typedef enum {
 	 	 	 DRAW_FILL_EMPTY = 0,
 	 	 	 DRAW_FILL_FULL,
 	 	} DRAW_FILL;

Draw character (ASCII): Set(Xstart Ystart) as letf-top point, draw a ASCII character.

void Paint_DrawChar(UWORD Xstart, UWORD Ystart, const char Ascii_Char, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)
Parameter:
 	Xstart: X coordinate of left-top pixel of character;
 	Ystart: Y coordinate of left-top pixel of character;
 	Ascii_Char：Ascii character;
 	Font: 5 fonts are available;
 	 	font8：5*8
 	 	font12：7*12
 	 	font16：11*16
 	 	font20：14*20
 	 	font24：17*24
 	Color_Foreground: color of character;
 	Color_Background: color of background;

Draw String: Set point (Xstart Ystart) as the left-top pixel, draw a string.

void Paint_DrawString_EN(UWORD Xstart, UWORD Ystart, const char * pString, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)
Parameter:
 	Xstart: X coordinate of left-top pixel of characters;
 	Ystart: Y coordinate of left-top pixel of characters;
 	pString：Pointer of string
 	Font: 5 fonts are available:
 	 	font8：5*8
 	 	font12：7*12
 	 	font16：11*16
 	 	font20：14*20
 	 	font24：17*24
 	Color_Foreground: color of string
 	Color_Background: color of background

Draw Chinese characters: this function is used to draw Chinese fonts based ON GB2312 fonts.

void Paint_DrawString_CN(UWORD Xstart, UWORD Ystart, const char * pString, cFONT* font, UWORD Color_Foreground, UWORD Color_Background)
Parameter:
 	Xstart: Coordinate of left-top pixel of characters;
 	Ystart: Coordinate of left-top pixel of characters;
 	pString：Pointer of string
 	Font: GB2312 fonts
 	 	font12CN：11*21(ascii)，16*21 (Chinese)
 	 	font24CN：24*41(ascii)，32*41 (Chinese)
 	Color_Foreground: color of string
 	Color_Background: color of background

Draw number: Draw a string of numbers, (Xstart, Ystart) is the left-top pixel.

void Paint_DrawNum(UWORD Xpoint, UWORD Ypoint, int32_t Nummber, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)
Parameter:
 	Xstart: X coordinate of left-top pixel;
 	Ystart: Y coordicate of left-to pixel;
 	Nummber：the numbers displayed. the numbers are saved in int format, the maximum is 2147483647;
 	Font: 5 fonts are available：
 	 	font8：5*8
 	 	font12：7*12
 	 	font16：11*16
 	 	font20：14*20
 	 	font24：17*24
 	Color_Foreground: color of font;
 	Color_Background: color of background;

Display time:Display time, (Xstart, Ystart) is the left-top pixel. This function is used for e-Paper which supports partial refresh

void Paint_DrawTime(UWORD Xstart, UWORD Ystart, PAINT_TIME *pTime, sFONT* Font, UWORD Color_Background, UWORD Color_Foreground)
Parameter:
 	Xstart: X coordinate of left-top pixel of character;
 	Ystart: Y coordinate of left-top pixel of character;
 	pTime：Pointer of time displayed;
 	Font: 5 fonts are available;
 	 	font8：5*8
 	 	font12：7*12
 	 	font16：11*16
 	 	font20：14*20
 	 	font24：17*24
 	Color_Foreground: color of fonts
 	Color_Background: color of background

Draw image:send image data of bmp file to buffer

void Paint_DrawBitMap(const unsigned char* image_buffer)
Parameter:
 	image_buffer: adrress of image data in buffer

User Guides of Arduino

Hardware connection

The demo codes provided are based on Arduino UNO. If you want to use another Arduino board, you may need to change the connection and port the codes by yourself.
The RAM of Arduino UNO is too small to realize drawing function of e-Paper. In this case, for most of the e-Paper, we only make the image display function and save the image to flash.
We recommend you to use [E-Paper Shield] if you use Arduino UNO. The seven-color e-Paper is not compatible with the e-Paper shield, please note it.

Arduino Corresponding Pins
e-Paper	Arduino UNO	Mega2560
Vcc	5V	5V
GND	GND	GND
DIN	D11	D51
CLK	D13	D52
CS	D10	D10
DC	D9	D9
RST	D8	D8
BUSY	D7	D7

Install Arduino IDE

arduino IDE Install Guide

Run the Program

Download the program on the product encyclopedia interface, and then unzip it. Arduino programs are located at ~/Arduino/…

Please select the corresponding program to open according to the ink screen model

Supporting types

1.02inch（128 × 80）：

EPD_1in02d_test()：Example for 1.02inch e-Paper/1.02inch e-Paper.

1.54inch（1.54inch e-paper c：152 × 152，others：200 × 200）：

epd1in54： Example for 1.54inch e-paper V1（Balck/White）: This version is stopped production which can be bought before 2019-11-22；
epd1in54_V2: Example for 1.54inch e-paper V2（Balck/White): This is the current version that can be bought now (2020-07-29). The e-Paper has V2 sticker on the backside.
epd1in54b： Example for 1.54inch e-paper B（Black/White/Red). It is currently out of production.
epd1in54b_V2: Example for 1.54inch e-Paper B V2 (Black/White/Red). The purchase date later than November 2019 is the V2 version, the current shipping version has the V2 logo on the back;
epd1in54c： Example for 1.54inch e-paper C（Black/White/Red）;

1.64inch（168 × 168）

EPD_1in64g_test(): Example for 1.64inch e-paper G (Black/White/Red/Yellow)

2.7inch（264 × 176）

epd2in7: Example for 2.7inch e-paper（Black/White）;
epd2in7b: Example for 2.7inch e-paper B（Black/White/Red）;
epd2in7b_V2: Example for 2.7inch e-paper B V2（Black/White/Red）;

2.9inch (296 × 128)

epd2in9: Example for 2.9inch e-paper (Black/White), this version is stopped production.
epd2in9_V2: Example for 2.9inch e-paper V2（Black/White）; The purchase date is later than December 2020 is the V2 version, the current shipping version has the V2 logo on the back;
epd2in9bc: Example for 2.9inch e-paper B（Balck/White/Red） and 2.9inch e-paper C（Black/White/Yellow）;
epd2in9b_V3: Example for 2.9inch e-paper B V3 （Balck/White/Red）; Purchase date later than July 2020 is the V3 version, the current shipping version has the V3 logo on the back;
epd2in9d: Example for 2.9inch e-paper D（Black/White）.

2.13inch（2.13inch e-Paper：250 × 122，others：212 × 104）：

epd2in13: Example for 2.13inch e-paper V1（Black/White）, this version is stopped production and it can be bought before 019-05-15;
epd2in13_V2: Example for 2.13inch e-paper V2（Black/White） This is the current version with sticker V2 on the backside (2020-07-29)；

epd2in13_V3: Example for 2.13inch e-paper V3（Black/White） This is the current version with sticker V3 on the backside (2020-07-29)；
epd2in13bc：Example for 2.13inch e-paper B（Black/White/Red）and 2.13inch e-paper C（Blackj/White/Yellow）;
epd2in13b_V3：Example for 2.13inch e-paper B V3（Black/White/Red）Purchase date later than April 2020 is the V3 version, the current shipping version has the V3 logo on the back;
epd2in13d： Example for 2.13inch e-paper D（Black/White）;

2.66inch (152 × 296)

epd2in66: Example for 2.66inch e-Paper (Black/White);
epd2in66b: Example for 2.66inch e-Paper B (Black/White/Red);

3inch (400 × 168)

EPD_3in0g_test(): Example for 3inch e-Paper G(Black/White/Red/Yellow);

3.52inch (360 × 240)

EPD_3in52_test(): Example for 3.52inch e-Paper (Black/White);

3.7inch (280 × 480)

epd3in7: Example for 3.7inch e-Paper(Black/White);

4.01inch (640 × 400)

epd4in01f: Example for the 4.01inch e-Paper HAT (F) (Black/White/Green/Blue/Red/Yellow/Orange);

4.2inch（400 × 300）

epd4in2： Example for 4.2inch e-paper（Black/White）；
epd4in2bc： Example for 4.2inch e-paper B（Black/White/Red）；
epd4in2b_V2： Example for 4.2inch e-paper B V2（Black/White/Red）. The purchase date is later than November 2020, it is the V2 version, and the current shipping version has the V2 logo on the back;

5.65inch (600 × 448)

epd5in65: Example for for 5.65inch e-Paper F (Black/White/Green/Blue/Red/Yellow/Orange);

5.83inch（600 × 448）：

epd5in83： Example for 5.83inch e-paper（Black/White）, It is currently out of production.
epd5in83_V2： Example for 5.83inch e-paper V2（Black/White）, The purchase date is later than December 2020 is the V2 version, the current shipping version, with the V2 logo on the back.
epd5in83bc： Example for 5.83inch e-paper B（Black/White/Red）and 5.83inch e-paper C（Black/White/Yellow）;
epd5in83b_V2： Example for 5.83inch e-paper B V2（Black/White/Red). The purchase date is later than August 2020 for the V2 version, the current shipping version, with the V2 logo on the back

7.5inch（V1：640 × 384， V2：800 × 480）：

epd7in5： Example for 7.5inch e-paper（Black/White）. The purchase date is earlier than 2019-12-07 as the V1 version, which is currently discontinued.
epd7in5_V2： For example for 7.5inch e-paper B（Black/White/Red）and 7.5inch e-paper C（Black/White/Yellow）, The purchase date later than 2019-12-07 is the V2 version, and the current shipping version has the V2 logo on the back;
epd7in5bc： Example for 7.5inch e-paper V2（Black/White）. The purchase date of 7.5inch e-paper B is earlier than 2019-12-07, which is the V1 version, which is currently discontinued, and 7.5inch e-paper C is normally available.
epd7in5b_V2： Example for 7.5inch e-paper B V2（Black/White/Red）; The purchase date is later than 2019-12-07 is the V2 version, with the V2 logo on the back; the purchase date is later than March 2021 is the V3 version, the current 7.5inch e-paper B shipping version, with the V3 logo on the back, the same use this program;

7.3inch (400 × 168)

epd_7in3g_test.py: Example for 7inch3 e-paper G (Black/White/Red/Yellow).

7.5inch (880 × 528)

epd7in5_HD: Example for 7.5inch e-Paper HD (Black/White);
epd7in5b_HD: Example for 7.5inch e-Paper B HD (Black/White/Red);
*Note: The above time is for reference only, please refer to the screen logo for the specific version.
For example, 1.54inch e-Paper Module. Open the epd1in54 folder and run the epd1in54.ino file.
Open the program, select the development board model Arduino UNO

Select the corresponding COM port

Then click compile and download

Since the flash of arduino UNO is very small, several large-size screens use MEGA2560 for better results:<

Code Description

Files

Take the 1.54-inch ink screen controlled by Arduino UNO as an example, open the epd1in54 directory:

in which:
epd1in54.ino: open with Arduino IDE;
epd1in54.cpp(.h): is the driver of the ink screen;
epdif.cpp(.h): is the hardware interface definition, which encapsulates the read and write pin levels, SPI data transmission, and pin initialization;
font8.cpp, font12.cpp, font16.cpp, font20.cpp, font24.cpp, fonts.h: are the models of characters of different sizes;
imagedata.cpp(.h): is the image data, which can convert the 2-bit depth BMP image into an array through Img2Lcd (downloadable in the development data).
The program is divided into the bottom hardware interface, the middle layer ink screen driver, and the upper layer application;

Bottom Hardware Interface

hardware interfaces are defined in epdif.cpp(.h) file.

Write GPIO

void DigitalWrite(int pin, int value)

The first parameter is GPIO, and the second parameter is level.

Read GPIO

int DigitalRead(int pin)

The parameter is GPIO, and the return value is level.

Delay

DelayMs(unsigned int delaytime)

Delay time, the unit is ms.

SPI transmit data

SpiTransfer(unsigned char data)

The type of parameter is char

Hardware initialize

int IfInit(void)

The initialize function of SPI, input/ouptu are packaged here。

Middle EPD driver

Instantiate e-Paper class

The Arduino codes are based on C++, should instantiate e-Paper class is necessary.

Epd epd;

Initialize e-Paper, it should be used to initialize e-Paper or wakeup e-Paper from sleep mode.

2.13inch e-Paper，2.9inch e-Paper

epd.Init(lut_full_update); //Fully update
epd.Init(lut_partial_update); //Partial update

4.2inch e-Paper

epd.Init();

Clear, clear the e-Paper to white

epd.clear();

In some of project, the operation is divided to two part, they work in the same way

epd.ClearFrameMemory(0xFF); 
epd.DisplayFrame();//Display it

Transmit one frame of image and display

void Display(const unsigned char* frame_buffer);
void DisplayFrame(const unsigned char* frame_buffer_black, const unsigned char* frame_buffer_red); //Three color e-Paper

Sleep

epd.Sleep();

Set the e-Paper enter sleep mode. The consumption of the e-Paper will be reduced. However, you still need to update the display periodically to avoid a ghost problem.

Application functions

The drawing functions are defined in this part.
The coordination of the image buffer：

The functions are defined in epdpaint.h file

Initailze image buffer

Paint(unsigned char* image, int width, int height);

The first parameter is the image buffer, the second one is the width of the picture, and the third one is the height.

Paint paint(image, 0, 0);    // width should be the multiple of 8

The second and third parameters are set to 0, you can re-configure them with functions below:

Set the width, height, and rotation degree.

int  GetWidth(void); //Get the width
void SetWidth(int width);//Set the width
int  GetHeight(void);//Get the height
void SetHeight(int height);//Set the height
int  GetRotate(void);//Get the degree
void SetRotate(int rotate);//Set the rotate degree

Get the image data

unsigned char* GetImage(void);

Draw circle

void DrawPixel(int x, int y, int colored);

Coordination（x,y）

Draw character

void DrawCharAt(int x, int y, char ascii_char, sFONT* font, int colored);

Set（x,y）as the start point, draw characters ascii_char, set the fonts as font, and color is colored.

Drawstring

void DrawStringAt(int x, int y, const char* text, sFONT* font, int colored);

Set（x,y）as the start point, draw the string text, font is a font， color is colored

Draw line

void DrawLine(int x0, int y0, int x1, int y1, int colored);

Use （x0,y0）as start point, （x1,y1） as endpoint;

Draw cross line

void DrawHorizontalLine(int x, int y, int width, int colored);

Set（x0,y0）as start points， draw a line, the width is width, and the color is colored</ br>

Draw a vertical line

void DrawVerticalLine(int x, int y, int height, int colored);

Use（x0,y0） as a start point, draw a vertical line, width is height, and the color is colored./ br>

Draw a empty rectangle

void DrawRectangle(int x0, int y0, int x1, int y1, int colored);

User（x0,y0） as a start point,（x1,y1） as an end point, draw a rectangle, color of edges are colored.

Draw a full rectangle

void DrawFilledRectangle(int x0, int y0, int x1, int y1, int colored);

Use（x0,y0）as a start point, （x1,y1） as an end point, draw a rectangle, fill it with color: colored

Draw an empty circle

void DrawCircle(int x, int y, int radius, int colored);

Use （x,y）as the center， and draw an empty circle with a radius, color is colored

Draw a full circle

void DrawFilledCircle(int x, int y, int radius, int colored);

Use （x,y）as the center, and draw a solid circle with a radius, filled with color: colored.

Documentation

Program

Github

Datasheet

Software

Question about Software

Question:stm32 drives the ink screen, the MDK compilation display space is not enough?

Answer:

*Our demo uses stm32f103zet6. If the customer modifies other models in MDK, such as stm32f103rbt6, the ram space becomes smaller, and the stack size and heap size in the startup file need to be modified on the original basis.

Question:ImportError: No module named Image?

Answer:

*Install the imaging library using the command sudo apt-get install python-imaging

Question:When to transmit Data Start Transmission 1 and when to use Data Start Transmission 2. In KW mode, what is "OLD" data and what is "NEW" data. ?

Answer:

If it is a three-color screen, when you need to transmit B/W data, use Data Start Transmission 1, when transmitting RED data, use Data Start Transmission 2, because the 2.13inch e-Paper HAT (D) can only display black and white, Therefore, when working in KW mode Data Start Transmission 1, the last data is sent, that is, the so-called old, and 0x00 is directly sent in the program. When Data Start Transmission 2, the data that needs to be refreshed, the so-called "NEW" is sent. data.

Question:Can't display Chinese on the e-ink screen?

Answer:

The Chinese character library of our demos uses GB2312 encoding method, please change your xxx_test.c file to GB2312 encoding format, compile and download it, and it will display normally

Question:The e-Paper display is too dark or too light?

Answer:

You can adjust the value of Vcom in the program to change the display contrast, and the screen improvement effect with local brushing is particularly obvious.

Question:e-Paper shows black border?

Answer:

The border display color can be set through the Border Waveform Control register or the VCOM AND DATA INTERVAL SETTING register.

Question:After multiple positions are brushed, the font is lighter after brushing several times?

Answer:

In this case, the customer needs to reduce the position of the round brush and clear the screen after 5 rounds of brushing (increasing the voltage of VCOM can improve the color, but it will increase the afterimage).

Question:When the ink screen is in deep sleep mode, the first time the screen refreshes will be unclean. How can I solve it?

Answer:

The process of re-awakening the e-ink screen is actually the process of re-powering on the power. Therefore, when the EPD wakes up, it must first clear the screen, so as to avoid the afterimage phenomenon to the greatest extent.

Question:When testing the program, the program has been stuck in e-Paper busy?

Answer:

*It may be caused by the unsuccessful spi driver.

1. First check whether the wiring is correct.
2. Check whether the spi is turned on and whether the parameters are configured correctly (spi baud rate, spi mode and other parameters).

Question about Hardware

Question:Can Arduino 3.3V drive the ink screen?

Answer:

Yes, now there is a level conversion chip onboard, supporting 3.3V drive.

Question:What should be paid attention to when designing the driver board?

Answer:

The rated input voltage of the ink screen is 2.3~3.6V. If it is a 5V system, level conversion is required. In addition, the voltage should not be lower than 2.5V, so as not to affect the display effect of the ink screen.

Device selection can use the model in the schematic diagram we provide or choose according to the data sheet.

Question:Can I use analog SPI?

Answer:

Yes, pay attention to the correct timing.

Question:Why is the BUSY pin always busy?

Answer:

Check if SPI communication is normal.

Confirm whether the BUSY pin is normally initialized to input mode.
It may be that there is no normal reset, try to shorten the duration of the low level during reset (because the power-off switch is added to the drive circuit, the reset low level is too long, which will cause the drive board to power off and cause the reset to fail). If the busy function sends the 0x71 command, you can try to comment it out.

Question about Screen

Question:What is the usage environment of the e-ink screen?

Answer:

*【Working conditions】Temperature range: 0~50°C; Humidity range: 35%~65%RH.

【Storage conditions】: Temperature range: below 30°C; Humidity range: below 55%RH; Maximum storage time: 6 months.
【Transportation conditions】: Temperature range: -25~70°C; Maximum transportation time: 10 days.
【After unpacking】: Temperature range: 20°C±5°C; Humidity range: 50±5%RH; Maximum storage time: Assemble within 72 hours.

Question:Precautions for e-ink screen refresh

Answer:

*refresh mode

- Full brush: The electronic ink screen will flicker several times during the refresh process (the number of flickers depends on the refresh time), and the flicker is to remove the afterimage to achieve the best display effect.
- Bureau brush: The electronic ink screen has no flickering effect during the refresh process. Users who use the partial brushing function note that after refreshing several times, a full brush operation should be performed to remove the residual image, otherwise the residual image problem will become more and more serious, or even damage the screen (currently only some black and white e-ink screens support partial brushing, please refer to product page description).
- refresh rate
- During use, it is recommended that customers set the refresh interval of the e-ink screen to at least 180 seconds (except products that support the local brush function).
- During the standby process (that is, after the refresh operation), it is recommended that the customer set the e-ink screen to sleep mode, or power off operation (the power supply part of the ink screen can be disconnected with an analog switch) to reduce power consumption and prolong the life of the e-ink screen. (If some e-ink screens are powered on for a long time, the screen will be damaged beyond repair.)
- During the use of the three-color e-ink screen, it is recommended that customers update the display screen at least once every 24 hours (if the screen remains the same screen for a long time, the screen burn will be difficult to repair).
Application
- The e-ink screen is recommended for indoor use. If it is used outdoors, it is necessary to avoid direct sunlight on the e-ink screen, and at the same time, take UV protection measures, because charged particles will dry out under strong light for a long time, resulting in loss of activity and failure to refresh. This situation is irreversible. When designing e-ink screen products, customers should pay attention to determining whether the use environment meets the requirements of e-ink screen.

Question:What is the refresh rate/lifetime of the e-ink screen?

Answer:

Ideally, with normal use, it can be refreshed 1,000,000 times (1 million times).

Question:After using for a period of time, the screen refresh (full refresh) has a serious afterimage problem that cannot be repaired?

Answer:

Power on the development board for a long time, after each refresh operation, it is recommended to set the screen to sleep mode or directly power off processing, otherwise the screen may burn out when the screen is in a high voltage state for a long time.

Question:After the ink screen enters deep sleep mode, can it be refreshed again?

Answer:

Yes, but you need to re-initialize the electronic paper with software.

Question:Why is the image displayed offset

Answer:

Maybe the SPI rate is too high, resulting in data loss, try to reduce the SPI rate.

Insufficient or unstable power supply leads to data loss.
The data cable is too long to cause data loss, the extension cable should not exceed 20cm.

Question:What is the waveform file of the e-ink screen and what does it do?

Answer:

The display gray scale of electrophoretic electronic paper is determined by the spatial position of the particles in the microcapsule or microcup. The electrophoresis phenomenon occurs between black particles and white particles under the action of voltage. This voltage sequence that promotes the electrophoretic movement of the particles is the driving force of the electronic paper. waveform. The driving waveform is the core part of the electronic paper display, and the optimization of the driving waveform will directly affect the display effect of the display. The driving waveform file is used to describe the parameters formed by the voltage sequence that promotes the electrophoretic movement of the particles, and it needs to be called regularly when the electronic paper is refreshed.

Different batches of e-paper diaphragms and electrophoretic matrices require different voltage values when driving the display due to materials, manufacturing processes, etc. The waveform of the e-ink screen is reflected in the relationship between grayscale, voltage and temperature. Generally speaking, after each batch of electrophoresis matrix is generated, there will be a corresponding waveform file in the form of a .wbf file. The film manufacturer will provide the waveform file and electrophoresis matrix to the manufacturer of the electronic paper screen, and then the The manufacturer of electronic paper screen integrates the protection board, substrate and driver and then provides it to customers; if the waveform file does not correspond to the screen, it is likely that the display cannot be displayed or the display effect is unsatisfactory. Generally, the waveform file has OTP built into the driver IC of the ink screen when leaving the factory, and some programs we provide also call external waveform files to drive the e-ink screen.

Question: What do LUT and OTP stand for?

Answer:

LUT is the abbreviation of LOOK UP TABLE, and OTP is the abbreviation of ONE TIME PROGRAM. The original intention of LUT is to load waveform files, and the waveform files are divided into OTP and REGISTER. Among them, OTP is the built-in waveform storage method, and REGISTER is the external waveform storage method.

Question:What is the process of brushing e-paper?

Answer:

There are mainly two types of ink screens.

One is to brush the background image first.
The other is to alternately refresh old data and new data.

Question:How do I play in different positions at the same time?

Answer:

Simultaneous brushing in different locations needs to be operated in the program design, that is, first brushing the data of different locations into the electronic paper IC, and finally doing the Update/TurnOnDisplay uniformly.

Question: Does the three-color e-Paper have a red/yellow color difference?

Answer:

Yes, when e-Paper is batched, there will be some color difference, which is a normal phenomenon. Store the e-paper faces up to reduce the reddish/yellowishness to a certain extent.

Others

Question: Are bare screens shipped with a film?

Answer:

with film.

Question: What is the specification of the screen cable interface?

Answer:

0.5mm pitch, 24Pin.

Question: What type of connector does the ink screen use?

Answer:

Cable socket 0.5-24pin rear flip type 2.0H (FPC connector).

Question: Does e-Paper have a built-in temperature sensor?

Answer:

At present, all screens have built-in temperature sensors, and external LM75 temperature sensors can also be used with IIC pins.

Question:Why can't the image be displayed after full brushing?

Answer:

The full brush initialization function needs to be added when the ink screen is switched from partial brush to full brush.

Question: Why is the printing information normal when running the python program but the ink screen does not respond?

Answer:

It may be a demo based on the BCM2835 library that has run the C language before. At this time, you need to restart the Raspberry Pi and then run the python demo.

To：

Dear Customers, There may be a lag of several hours before we could process your order, depending on the time difference between your location and ours. Sincerely hoping your understanding!

Email(support)

services01@spotpear.com

TAG： A7670E LTE Cat-1 HAT for Raspberry Pi Multi Band 2G GSM / GPRS LBS Raspberry Pi 5 Audio Jack Raspberry Pi Display Driver Board Raspberry Pi Camera V1 RP2040-PiZero PCIe M.2 NVMe Dual SSD Jetson Nano IO Board STM32 1.5inch LCD USB TO 4CH RS485 User Guide Raspberry Pi LCD ESP32 C3 LCD Power Gyroscope Milk V Raspberry Pi 5 5V5A Power Raspberry Pi 5 Cooling ESP32 ST7789 Raspberry Pi User Guide Arduino 0.96inch RGB OLED ESP32 C3

Price：

$17/21.89

Model：

1.64inch-e-Paper-/-Module-(G)

1.64inch e Paper e Ink Display Module SPI for Arduino / STM32 / Jetson Nano / Raspberry Pi

TAG： Raspberry Pi Pico Raspberry Pi 5 Active Cooler Raspberry Pi Real time clock SC09 Serial UART Bus Servo Motor 2.3kg 300Angle Raspberry Pi 15.6 inch FHD Monitor LCD Capacitive TouchScreen Display Type-C HDMI Computer PC UPS HAT D RM500Q AE IoT EMBB 5G 4G 3G M.2 LTE-A/NSA SA GNSS DFOTA VoLTE Quectel Raspberry Pi Autofocus Camera ESP32-H2-MINI-1-N4 Module Clock trinket ESP32-C6-MINI-1Support WiFi 6 Bluetooth 5 Zigbee Thread Raspberry Pi DSI display Milk-V Duo Ethernet Luckfox Omni3576 Rockchip RK3576 Core3576 4.26inch E-Paper Jetson Xavier NX Kit Raspberry Pi 5 5V5A Power Raspberry Pi 5 PWM Cooling Fan Electronic EYE 0.71inch Round LCD Display Screen Arduino Raspberry Pi ESP32 Pico STM32 R7FA4 PLUS B Development Board Based on R7FA4M1AB3CFM Compatible with Arduino UNO R4 WiFi