• sales

    +86-0755-88291180

Raspberry Pi PI4-CASE-ARGON-ONE-M.2 User Guide

Introduction

The PI4-CASE-ARGON-ONE-M.2 metal case can greatly speed up the boot and storage speed of the Raspberry Pi, which is to extend the M.2 interface through the USB interface and use an external SSD as the main storage drive. In this case, the Raspberry Pi 4 can be booted through the USB interface, which greatly improves the reading and writing speed and makes the boot speed much faster than using the SD card.

How to boot Raspberry Pi 4 with SSD

1.Assemble and install the SSD into the expansion board as shown below. (This product doesn't contain M.2 SSD and Raspberry Pi, please purchase separately if necessary)


2.Connect the TF card to the PC and write the system image. After the image has finished writing, connect the SD card to the Raspberry Pi, connect the M.2 expansion board and the case, and then connect it with the Raspberry Pi4 using the USB Adapter.


3.Enter the terminal of the Raspberry Pi to update system and firmware.

sudo apt-get update


sudo apt-get full-upgrade


sudo rpi-update


After the update is complete, reboot the Raspberry Pi.

sudo reboot


4.Enter the following command to install the latest bootloader.

sudo rpi-eeprom-update -d -a


5.And then reboot the system.

sudo reboot


6.After system reboot,enter the following command to open the setup tool of the Raspberry Pi

sudo raspi-config


7.Choose "Advanced Options", then click 'Enter'.


8.Choose "Boot ROM Version", then click 'Enter'.


9.Choose "No"


10.Click 'Enter'


11. Then choose "Boot Order", click 'Enter'.


12.Choose "USB Boot", click 'Enter'.


13.Click 'Enter' to confirm "USB device is default boot device".


14.Choose "Finish"to end the configuration.


15.Choose "No" when the system ask "Would you like to reboot now?".


16.Click the Menu button on the desktop, choose "Accessories" and "SD Card Copier".


17.As shown in the figure below, select to copy the device from the 16sd card to the SSD, and then click Start.

Note: If the device to be copied is not recognized, please check whether the USB interface is connected.


18. After the click the 'start', the system will automatically partition and then copy the corresponding content, wait for the system to finish copying and then click OK to complete. It may takes about 10 minutes.


19. And then shut down the system.


20. Remove the shell, then take out the SD card, and reconnect the USB connector. And then reinstall the shell and power on the system, you can see the system booted through the SSD.

Install the fan and power button driver

1.The fan and power button can only work with the driver. You can directly refer to the manual which comes with the case.


2.Open terminal of Raspberry Pi, install the driver by the following command

curl https://download.argon40.com/argon1.sh | bash


3.After installation, two shortcuts are added to the desktop, "configure" and "uninstall", they can be used to configure and uninstall the driver.


You can also use commands to configure and uninstall driver

argonone-config  #configure driver
argonone-uninstall  #uninstall driver
  • The default setting of the fan is:
CPU temperatureFan speed
55°C10%
60°C55%
65°C100%
  • Power button
Raspberry Pi statusButtonFunction
ShutdownPressStart
WorkingLong-press (>3s)Shutdown
WorkingPress(<3s)No function
WorkingDouble-clickRestart
WorkingLong-press(>5s)Force shutdown
TAG: ESP32-S3 Industrial-Grade IOT RS485 CAN Communicator WiFi Bluetooth X1300 X1300-A2 Raspberry Pi 5 HDMI to CSI-2 Shield 1080P@60fps & Audio & Video Also NVIDIA Jetson Xavier NX AI 21TOPS Supercomputer Edge Computing eMMC-16GB RAM 8/16GB Allwinner H618 Raspberry Pi 5 UPS HAT E 4-Port For 21700-Li-Battery (NOT includ) 5V6A Uninterruptible Power Supply STM32 1.54inch OLED Bus Servo DC-BUCK-Adapter 7.2V Voltage mini module For SC15/SC09 Servo USB to JTAG Computer Raspberry Pi 5 UART Core3566104032 ESP32-S3 Raspberry Pi Mipi Raspberry Pi Camera Module 3 Sensor Assembly IMX708 Official Original 11.9MP Camera Milk V Duo IO Board Tutorial NanoKVM-Lite-Quick-Start Computer Desktop Monitor Display JETSON-NANO-MINI Raspberry Pi Pico 2 RP2350 2.8 inch LCD Capacitive TouchScreen Development Board 240x320 Display QMI8658 6-Axis /PCM5101 Audio /SD /RTC /Battery Port Raspberry Pi 3 display HAT