• sales

    +86-0755-88291180

Raspberry Pi Li-polymer Battery HAT User Guide

Instruction

The Li-polymer Battery HAT integrates SW6106 power bank management chip, allows providing 5V regulated power supply to your Raspberry Pi or other 5V devices, from a high capacity Li-polymer battery. It will charge the battery as well, supports bi-directional quick charge.

Features

  • Onboard SW6106 chip, supports bi-directional quick charge, supports multi quick charge protocols like PD/QC/FCP/PE/SFCP
  • Lithium battery protection circuitry, provides reverse protection, overcharge protection, and short circuit protection
  • Onboard indicators: quick charge, power capacity
  • PH 2.0 battery connector, for connecting the 3.7V 3000mA high capacity Li-polymer battery (MSDS certified)

Specifications

  • Output voltage: 5V
  • Charge voltage: 5V
  • Applicable battery: 3.7V Li-polymer battery (4.2V when full charged)
  • Dimension: 65.0mm × 56.5mm
  • Mounting hole size: 3.0mm

Interfaces and Indicators

  • Interfaces
InterfaceDescription
Micro USBCharge
USB Type-APower output
USB Type_CSuports chrage, quick charge and power output
  • There are five battery indicators.
CapacityLED1LED2LED3LED4LED5
80%~100%ONONONONON
60%~80%ONONONONBlink
40%~60%ONONONBlinkOFF
20%~40%ONONBlinkOFFOFF
5%~20%ONBlinkOFFOFFOFF
1%~5%BlinkOFFOFFOFFPFF
0%OFFOFFOFFOFFOFF
  • Quick start indicator
When you connect power adapter to Type_C interface for quick charging, the Quick Charge indocator will turn on. If it keeps on, maybe that your adapter doesn't support quick charge.
  • Standby button
Single-press it to output 5V, and double-press it to set it to sleep mode.

How to use

Discharge

Connect it to Raspberry Pi
  • Step1: Insert the Li-polymer battery to 2.0mm battery socket.
  • Step2: Single-press Standby button, set it to discharge mode
  • Step3: Attach it on Raspberry Pi for powering.
For other devices.
  • Step1: Insert the Li-polymer battery to 2.0mm battery socket.
  • Step2: Single-press Standby button, set it to discharge mode
  • Step3: Connect it to other devices by USB cable or wires.

Charge

Charge
  • Step1: Insert the Li-polymer battery to 2.0mm battery socket.
  • Step2: Connect power adapter to micro USB or Type-C interface by USB cable
Quick charge
  • Step1: Insert the Li-polymer battery to 2.0mm battery socket.
  • Step2: Connect power adapter (support quick charge) to type_C interface by USB cable
  • Step3: Check if the Quick charge indicator turns on.

Notices

  • Module enter sleep mode when the working current is less than 40mA and stop to discharge.
  • The Quick charge mode only works when you connect a power adapter that supports quick charge.
  • To power Raspberry Pi, you can attach it on the GPIO or connect Type_A interface to Pi by USB cable.
  • This module cannot work as UPS. It will turn off Raspberry Pi when low-voltage.
  • The battery is about 4.2v when fully charged. Note that you should discharge the battery to 3.0, otherwise it is damaged.
  • Please disconnect any devices when you replace battery.
  • DO NOT change the battery provided with other battery without protective panel.
  • Please check the poles of the battery interface carefully when you connect batteries.
TAG: Industrial RS232 to RS485 Spotpear Pan-Tilt Kit Modbus RTU Raspberry Pi MLX90640 Raspberry Pi 64MP Camera Raspberry Pi Pico 2 RP2350 2.8 inch LCD Capacitive TouchScreen Development Board 240x320 Display QMI8658 6-Axis /PCM5101 Audio /SD /RTC /Battery Port LCD1602 I2C Module PWM Adjustable backlight 3.3V/5V For Arduino/ Raspberry Pi/ Pico/ Jetson Nano/ ESP32 Sipeed NanoCluster Mini Cluster Board mini data center For Raspberry Pi CM45 / Computer /LM3H /M4N 101M-8001280-IPS-CT-K User Guide VGA to RGB Modbus RTU Relay 32CH RV1103 Raspberry Pi 4 USB Audio ESP32 S3 Development Board 1.5 inch Round Rotary OLED TouchScreen Smart Knob Display 1.5inch Display 466x466 LVGL for Arduino TVOC Sensor gas Sensor Expansion board UART High Sensitivity For Arduino /Raspberry Pi /Pico /ESP32 Luckfox Pico SPI LCD Milk V Duo Raspberry Pi 5 Box Case Ki-A PCIe to RJ45 Gigabit Ethernet All Ports To Pi's USB Side ESP32 C3 1.44inch LCD