CM3+ Features

• Broadcom BCM2837B0
  • Cortex-A53 (ARMv8) 64-bit SoC @ 1.2GHz
• 1GB RAM
• eMMC Flash
  • CM3+/Lite: None, but brings the SD card interface to the Module pins so a user can wire this up to an eMMC or SD card
  • CM3+/8GB: 8GB
  • CM3+/16GB: 16GB
  • CM3+/32GB: 32GB
• 200PIN SODIMM connector (35U hard gold plating I/O pins)
  • 48 x GPIO
  • 2 x I2C
  • 2 x SPI
  • 2 x UART
  • 2 x SD/SDIO (1x SD has been used for eMMC Flash on non-Lite variants)
  • 1 x HDMI 1.3a
  • 1 x USB2 HOST/OTG
  • 1 x DPI (parallel RGB display)
  • 1 x NAND(SMI)
  • 1 x 4-lane CSI Camera Interface (up to 1Gbps per lane)
  • 1 x 2-lane CSI Camera Interface (up to 1Gbps per lane)
  • 1 x 4-lane DSI Display Interface (up to 1Gbps per lane)
  • 1 x 2-lane DSI Display Interface (up to 1Gbps per lane)
• Compared to CM1, the CM3+ supports more OS, like Windows 10 (the free IOT-specific version from Microsoft)

7inch HDMI LCD (C) Features

• 7inch IPS screen, 1024x600 hardware resolution
• Capacitive touch control
• Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers
  • When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free
  • When work as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free
• Backlight can be turned off to lower power consumption

Compute Module IO Board Plus Features

• Compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation
• Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs
• Arduino connectivity, also supports Arduino shields
• 1-WIRE interface, for connecting single-bus devices like DS18B20
• 4x keys, 4x LEDs, 1x Buzzer, for I/O testing
• Onboard USB HUB, allows connecting more USB devices
• IR receiver, IR remote control is available
• Onboard USB TO UART, for serial debugging
• Sensor interface
• 10-bit ADC, 38KSPS, 11-ch (6-ch for Arduino interface, 5-ch for sensors)
• 16-bit DAC, 2-ch
• Onboard RTC, one of the most common and useful functions

What's on the Compute Module IO Board Plus

1. Compute Module interface: for connecting Compute Module (CM3 / CM3L / CM3+ / CM3+L)
2. Compute Module GPIO header: breakout all the Compute Module pins
3. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs
4. CSI interface: camera ports, for connecting Raspberry Pi Camera
5. DSI interface: display ports, for connecting Raspberry Pi LCD
6. HDMI port
7. USB ports: for connecting USB devices
8. USB SLAVE interface: allows you to burn system image in to Compute Module 3/3+
9. USB TO UART interface: for serial debugging
10. Arduino header: for connecting Arduino shields
11. AD/DA input/output screw terminals
12. 1-WIRE interface: for connecting single-bus devices like DS18B20
13. Sensor interface
14. Power port: 5V 2.5A
15. FE1.1S: USB HUB chip
16. 12MHz crystal
17. CP2102: USB TO UART converter
18. Micro SD card slot: insert a Micro SD card with pre-burnt system, to start up Compute Module 3/3+ Lite variant
19. TLC1543: AD converter
20. DAC8552: 16-bit DAC, 2-ch
21. DS3231: high-precision RTC chip, I2C interface
22. RTC battery holder: supports CR1220 batteries
23. Voltage regulator: 3.3V / 2.5V / 1.8V 
24. LFN0038K: IR receiver
25. Buzzer
26. Power indicator
27. ACT indicator: indicating the Micro SD card status
28. User LEDs
29. User Keys
30. BOOT selection
    • EN: enable the PC to access SD card/eMMC through USB SLAVE
    • DIS: the Compute Module will boot from SD card/eMMC
31. VGx power selection: config the I/O level
32. USB HUB enable jumper: HUB enable and USB SLAVE power selection
33. ADC/DAC configuration: config the power supply and reference voltage of ADC/DAC
34. Peripheral configuration: config the control pins of UART, user keys, user LEDs, 1-WIRE interface, IR receiver, and buzzer
35. Arduino AD selection
    • connect 1 and 2: Arduino A0-A5 as digital control pin
    • connect 2 and 3: Arduino A0-A5 as AD input

Selection Guide

1. Compute Module 3+ 8GB x1
2. Compute Module IO Board Plus x1
3. 7inch HDMI LCD (C) x1
4. DS18B20 x1
5. IR remote controller x1
6. LCD adapter x1
7. HDMI cable x1
8. HDMI adapter x1
9. USB adapter x1
10. RPi screws pack (4pcs) x1
11. 22PIN FFC x1
12. RPi Zero V1.3 Camera Cable 15cm x1
13. Power adapter 5V/3A micro x1
14. USB type A plug to micro B plug cable 35cm x1
15. USB type A plug to micro B plug cable 120cm x2
16. Jumper Wire 4-pin to separated pins x2
17. Jumper Wire 2-pin 2.54-pitch 200mm x2